Filter
Top Products
Important Safeguards
Before using the electrical appliance, the
following basic precautions should always be
followed:
Read all instructions.1.
Before using check that the voltage of wall outlet 2.
correspond to the one shown on the rating plate.
Do not operate any appliance with a damaged cord 3.
or plug or after the appliance malfunctions, or is
dropped or damaged in any manner. Return 4.
appliance
to the nearest authorized service facility for 5.
examination, repair or electrical or mechanical
adjustment.
If the supply cord is damaged it must be replaced by 6.
the manufacturer or a authorized service agent or a
qualified technician in order to avoid a hazard.
Unplug from outlet when not in use, before putting 7.
on or taking off parts, and before cleaning.
Do not let cord hang over edge of table or hot 8.
surface.
Do not immerse upper part of blender into water as 9.
this would give rise to electric shock.
Close supervision is necessary when your appliance 10.
is being used near children or infirm persons.
Avoid contacting moving parts. 11.
Keep hands and utensils out of container while 12.
blending to reduce the risk of severe injury to
persons or damage to the blender.
A scraper may be used only when the blender is not 13.
running.14.
The appliance cannot be used for chopping ice or 15.
blending hard and dry substance, otherwise the
blade could blunt.
To reduce the risk of injury, never place cutting blade 16.
on base without first putting bowl properly in place.
Be sure chopper lid is securely locked in place 17.
before operating appliance.
The use of accessory not recommended by the 18.
manufacturer may cause injuries to persons.
Do not operate the appliance for other than its 19.
intended use.
Do not use outdoors.20.
SAVE THESE INTRUCTIONS
unit, turn the shaft in an anti-clockwise direction
until tightened. To disassemble, just turn in the
adverse direction.
Simply plug the hand-held blender to power 2.
outlet.
Lower the hand-held blender into food and 3.
depress the switch at the top of the motor unit.
To stop the hand-held blender release the switch 4.
at the top of the motor unit.
Instructions for chopper
Max operation duration under high speed per 1.
timecannot exceed 1 minute, and 1 minute rest
time must bemaintained at two consecutive
cycles.
Place the chopper bowl on a clean, level surface.2.
Assemble the stainless steel blade into the 3.
chopper bowl, as shown in Fig.1.
Place food into the chopper bowl.4.
Note:5. remove the bones from meat, cut into
small pieces, then place into bowl, the max
quantity of product can’t exceed 200g with
each blend.
Attach the Lid onto the chopper bowl and turn it 6.
ina clockwise direction until it locks into position.
(see Fig.2) To detach the lid, turn in adverse
direction.
Insert the bottom part of the blender into the hole 7.
of the chopper lid, and turn in clockwise direction
to lock. (See Fig.3)
Plug the appliance to power outlet and depress 8.
the switch to begin operation.
To stop the appliance release the switch at the top 9.
of the motor unit.
Caution:
To reduce the risk of injury, never place cutting •
blade on base without first putting bowl properly
in place.
Be sure chopper lid is securely locked in place •
before operating appliance.
Instructions for beater
Max operation duration under high speed per time 1.
cannot exceed 3 minute, and 1 minute rest time
must be maintained at two consecutive cycles.
To assemble the beater with the motor unit, turn 2.
the whisk anti-clockwise direction until tightened.
To disassemble, just turn in the adverse direction.3.
Using Your Blender
Before the first use, clean the blender according to the
section of “quick cleaning”. The time running unit
without load can’t exceed 15 seconds.
Important: Blades are very sharp, handle with care
Ensure that the hand-held stick blender is unplugged
from the power outlet before assembling or removing
attachments.
Instructions for blender
Max operation duration under high speed per time
cannot exceed 1 minute, and 1 minute rest time must be
maintained at two consecutivecycles.
To assemble the detachable shaft with the motor 1.
Fig.1 Fig.2 Fig.3