Filter
Top Products
4
FEATURES
⁄ Lid with lid release lever
¤ Spout filter
‹ Base and cable tidy
› 360° connector
fi Cord storage
fl Water level indicator with
illuminating light
‡ Temperature gauge
· + Temperature control button
‚ - Temperature control button
„ Start/Stop button
BEFORE FIRST
USE
Before using the appliance
for the first time, fill with
water, boil and pour away.
Water
Temperature
Getting the right water
temperature is essential for
you to enjoy your favourite
hot drinks with maximum
flavour and taste. Eg. if you’re
a green tea drinker, water that
is brewed too hot will scorch
the leaves and create a bitter
taste. If you’re a coffee lover,
then getting the water
temperature is crucial to
getting the best flavours from
the ground coffee.
See the table on the front of
this booklet for a quick
reference guide for some of
the most popular hot drinks
to allow you to get the most
from your IntelliBoil Jug
Kettle.
OPERATING THE
APPLIANCE
The integrated water level
indicators allow you to easily
see the amount of water in
the kettle.
• Always ensure that the
appliance is filled until the
water is visible through the
level indicator.
• Boil only as much water as
you need as this saves
electricity.
1 Place the appliance on the
base unit, ensuring the
appliance locates onto the
360° connector.
• The 360
° connector allows
the appliance to be located
at any position - ideal for left
and right handed users and
convenient positioning on
worktop.
2 Plug in and switch on at the
wall socket.
3 The gauge shows the
temperature of the water,
if the current water
temperature is below 40°C
the display will read LO.
4 The kettle is automatically set
to heat the water to 100°C. To
heat the water in the kettle to
85°C or 95°C, use the + and
-programming buttons to
adjust the selected heating
temperature.
• The red dot will highlight the
user selected setting and the
selected temperature will
flash on the digital gauge for
3 seconds.
• After the desired temperature
is selected, the display will
return to showing the current
water temperature.
5 Press the start/stop button to
begin heating the water. The
kettle will beep and show the
selected temperature for 3
seconds.
6 When the required
temperature has been
reached, the kettle will beep
3 times and switch off.
• After the kettle has switched
off, the display will show the
current temperature of the
water.
• It is not possible to reheat the
water in the kettle until it has
dropped below 80°C on the
85°C setting and 90°C on the
95°C. This prevents
unnecessary re-heating and
energy usage.
• It is not possible to use the
kettle to reduce the
temperature of previously
heated water.
• On the 100
o
C setting it is
possible to re-boil the water
as soon as the kettle has
switched off.
• When there is no function
activated for 15 minutes, the
LED display and the internal
illumination will switch off.
The display will wake up if
any button is pressed or if
the kettle is lifted up and
replaced back on its base.
Filter removal
1 Open the lid.
2 Lift the filter upwards from its
location using the tab
provided.
3 To refit the filter, slot it into
the side wall guides and
press down firmly. Ensure the
filter is correctly located into
the central guide.
WARNING: Make sure that
the filter is put in correctly
otherwise the lid will not
close.
Dry Boil
The kettle cuts off and
beeps when switched on
while empty.
Remove the kettle from its
base to stop the beeping
and then fill with water for
boiling.
UK Helpline 0844 871 0954 Replacement parts 0844 873 0719 Ireland 1800 409 119
43870rev1 b:43870 rev1 11/03/2009 15:47 Page 6