Filter
Top Products
4
UK Helpline 0844 871 0960 Replacement Parts 0844 873 0726 Ireland Helpline 1800 409 119
4
OPERATING THE
APPLIANCE
BEFORE USE
Before using your Meno
One Cup for the first time
or if you have not used it
for some time, rinse the
machine by running some
water through the machine.
Follow the making a drink
instructions and dispose of
the hot water.
Making a drink
1 To fill the water tank, lift the
handle ‹ to the upright
position and carry to a tap
to fill or by pouring water in
from a jug in position. The
water tank flap will open
automatically when the
handle is raised.
Once you have the required
level of water and the unit
is back on the base „
securely, place the handle
down. This will close the
flap.
2 Ensure that the drip tray is
attached by sliding it into
place. ‚
3 Adjust the cup size selector
› to the correct size for
your cup, left being a small
cup (150ml), right being a
large cup (maximum
dispense at one time is
300ml). ›
4 Place a cup to hold the hot
water on the drip tray
below the spout. ‡
5 Press the start button fl.
The unit will become
illuminated and will begin to
heat and dispense the
required amount of water.
6 If the unit does not start
boiling, check the base is
connected correctly.
7 If you find the cup is
getting too full, or you have
not placed your cup in
position, the excess water
will overflow into the drip
tray. Alternatively, press the
stop button. fi
Ensure you empty the drip
tray after every use when
cooled by removing from
the bottom of the unit.
8 When dispensed, the
illumination will go off and
the unit will make a gulping
noise which is normal.
9 If you require another cup
afterwards, ensure enough
water is in the tank, and
press the start button again
to begin.
If you want to empty the
water from the unit, take off
the base and use the
handle to carry to the sink
and empty.
When you think it is empty,
shake to ensure all the
water has been dispensed.
Descaling
IMPORTANT: As this
appliance is fitted with a
concealed element it must
be descaled regularly. The
frequency of descaling
depends on usage and the
hardness of the water in
your area.
Excessive scale can cause
the appliance to switch off
before boiling and may
damage the element
invalidating the warranty.
It is essential that regular
descaling takes place.
1 Fill the water reservoir to
maximum level with cold
water.
2 Add one sachet of
proprietary liquid descaler,
which is suitable for plastic
kettles.
3 Set cup size selector › to
maximum and place
suitable vessel under the
spout.
4 Press the start button fl
and allow the unit to run
and dispense the full
volume of water.
5 Repeat steps 3 and 4.
6 Allow unit to stand for 10
minutes.
7 Press the start button fl
and allow the unit to run
and dispense the full
volume of water.
8 Repeat step 7 until the tank
is empty.
9 Tip unit upside down over a
sink and shake to remove
any water left in the boiling
chamber Â.
10 Fill the water reservoir to
maximum level with cold
water.
11 Set cup size selector to
maximum and place
suitable vessel under the
spout.
12 Repeat steps 7-10.
13 Continue to use as normal.
IMPORTANT: Ensure that
the electrical connections
are completely dry before
using the appliance.
HINTS AND TIPS
Cleaning and
maintenance
WARNING: Always
disconnect the plug from
the mains and allow the
appliance to cool before
cleaning.
Wipe the outside with a
damp cloth.
IMPORTANT: Do not use
abrasive cleaners on the
outside of the appliance
which may scratch the
surface.
43922 rev3_x 14/10/2010 09:33 Page 4