Filter
Top Products
Using the bun warmer
B
Locate the bun warmer ‰ and place on
top of the toaster ensuring it is securely in
place.
Place the buns or other items onto the
bun warmer. Set the browning control(s) to
the bun warmer position 2 ›. Depress
bread carriage lever(s) until they hold down.
Wait for the toaster to switch off
automatically or press the cancel button to
switch the toaster off before removing the
buns.
WARNING: Take care not to touch
the metal of the bun warmer as it will
be hot.
Do not put more than two buns on the
bun warmer at any one time.
2-/4-slice selection
On the 4-slice model you don’t need to
heat up all the slots to toast one or two
slices. Just use one side of the toaster C.
To toast three or four slices of bread
depress both bread carriage levers D.
Hints & tips for perfect toasting
• For best results ensure the bread slices
are of even thickness, freshness and size.
•Stale bread toasts more rapidly than
fresh bread. Therefore, the browning
control should be set at a lower setting
than usual.
• Thin bread toasts quicker than thick.
• In order to achieve uniform browning, we
recommend you wait a minimum of 30
seconds between each toasting so that
the control automatically resets.
• If toasting one slice only, you may need
to adjust the browning control to a
slightly lower setting.
•You may notice a slight variation in toast
colour on one side of a single slice.
• All sorts of bread can be used as well as
teacakes, small rolls etc. Slices should
not however be so thick as to cause
burning or jamming within the bread
slots.
• When toasting more than one slice it is
recommended they are of equal size and
freshness.
Crumb trays
E
WARNING: Crumbs will accumulate
in the crumb tray and could catch fire if
not emptied regularly.
When the toaster has cooled down
completely, tap the sides of the case lightly
to dislodge any crumbs lodged in the
toasting chamber and remove the crumb
trays „. Empty the tray and replace it.
Never operate the toaster without the
crumb trays fitted.
5
Before first use
• Before using the toaster for the first time
operate the toaster without bread. Note:
the bread carriage levers ¤ will not stay
down unless the toaster is plugged in and
the wall switch is on. Ventilate the room
during this period.
• As with all new electric heating elements,
your toaster emits a ‘new’ smell when it
is first switched on. This is quite normal
and not a cause for concern.
Countdown display
Five red lights illluminate after depressing
the bread carriage lever and extinguish one-
by-one indicating the progress of toasting.
On the 4-slice model, when using both
sides independently, the lights refer to the
first lever that is depressed. When the first
side has finished toasting, the lights will then
display progress for the other side.
Toasting
The 4-slice toaster has two sides with
controls repeated for each half. Each half
can be used together or independently.
1 Select the desired level of browning on
the browning control ‹ marked 1 to 8.
The setting required will vary according to
the moisture content and thickness of the
bread.
2 After selecting the desired level, place
your bread in the slots ⁄ and depress
the bread carriage lever downwards until
it locks.
3 After the set time has been reached the
bread will pop up automatically ready for
removal from the slots. The bread
carriage lever will have returned to its
upper position and the heating element
will have switched off.
• If the bread in your toaster becomes
jammed disconnect your toaster at the
socket, allow it to cool, then remove the
bread.
• When not in use, remove the plug from
the mains socket.
• Allow the toaster to cool fully before
putting away.
WARNING: Do not wrap the cable
around the main body of the appliance
during or after use.
Using the frozen button
To toast frozen bread do not adjust the
browning control from your normal preferred
setting, place the bread normally in the
bread slots, then depress the bread carriage
lever and press the relevant frozen button ‡
when prompted by the flashing light. The
button will illuminate and the toaster will
operate for a longer period.
Using the re-heat button
(2-slice only)
If your toast has popped up and gone
cold, the toaster offers a re-heat facility. To
use, depress the bread carriage lever and
press the re-heat button fl when prompted
by the flashing light. The button will
illuminate and the toaster will operate for a
short period re-heating the bread.
Using the cancel button
If you wish to interrupt the toasting
process, press the appropriate cancel
button fi.
4
B
E
C
D