Filter
Top Products
FIGURE 4
BLOWER
MOUNTING
STUD
MOUNTING
SCREWS (3)
Product specifications subject to change without notice. 4820 Red Bank Road, Cincinnati, Ohio 45227
Printed in U.S.A., Rev. 01/2004, Part No. 84762
INSTALLATION IN A NEW
CONSTRUCTION SITE (continued)
3. Snap duct adapter over flanges on housing. Run 3" round
duct from housing to wall or roof cap.
Refer to Figures Figures 1 and 2.
IMPORTANT: Be sure nothing obstructs the discharge
of the fan. Take precautions to assure that insulation
does not get into ductwork or fan discharge opening.
4. Refer to Figure 3. Run 120vAC, 60Hz power wiring from
wall switch to ventilator housing. Remove the housing
junction box cover and connect wires from wall switch to
receptacle wires, using wire connectors - white to white,
black to black. Use a box connector on junction box.
Connect earth ground to green screw in junction box.
Replace junction box cover.
CAUTION: Be sure all wiring complies with local
electrical codes and housing is properly grounded.
5. Refer to Figure 4. Insert blower unit into housing, with stud
on mounting bracket on the side near the receptacle. Turn
bracket clockwise to lock blower into position, then tighten
the three screws. Plug in motor.
6. MODEL 8832NA: Compress spring clips on grille and isert
into slots provided in housing. Push grille up flush to ceiling.
MODEL 8833NA: Place hole in center of grille bezel over
stud on motor plate and fasten with nut provided. Snap
grille panel over the four (4) spring clips on grille bezel.
INSTALLATION IN EXISTING
CONSTRUCTION
To install the ventilator in an existing home requires
accessible area above the proposed installation location (attic
or crawl space). Because of the size and shape of the
ventilator housing it must be installed to a finished ceiling from
above.
Installation Hints
1. Review the section: INSTALLATION IN NEW
CONSTRUCTION SITE and follow all instructions where
applicable for your installation.
2. Refer to Figures 1 and 2 for duct work and Figure 3 for
wiring.
3. Drill small hole in ceiling in proposed location, then locate
this hole in attic or crawl space).
4. In attic, position housing over drilled hole and against ceiling
joist, being sure to have duct collar in the direction of the
ductwork. Mark ceiling for cutout by using housing as a
template - mark along the plaster flange. make cutout on
this outline.
5. Connect wires to receptacle wires in housing before
mounting.
6. Mount housing to ceiling joist.
One Year Limited Warranty
WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period
of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES
FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident,
improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above limitation may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH
PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone 1/800-543-8687, (b) give the model
number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present
evidence of the original purchase date.
Date of Installation Builder or Installer
Model No. and Product Description
IF YOU NEED ASSISTANCE OR SERVICE:
For the location of your nearest NuTone Independent Authorized Service Center:
Residents of the contiguous United States Dial Free 1-800-543-8687
Please be prepared to provide:
Product model number • Date and Proof of purchase • The nature of the difficulty
Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.
Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9.
Rev. 03/2001