Filter
Top Products
MODELS SSQTXE080 • SSQTXE110
Page 4
6. After less than 5-seconds, fan and LED turn on for 1 to
2-seconds and then turn off; which confirms “Restore”
was successfully accomplished.
7. If control does not respond as described, start process
over with step 1.
HOW TO CHANGE CONTROL COLOR
An almond paddle/frame assembly is included.
1. Use magnetic #1 Philips screwdriver and remove (4)
screws from white paddle/frame.
2. Remove white paddle/frame from control.
Caution: Do not touch or put anything inside control
housing; control damage may result.
3. Place almond paddle/frame on control.
4. Replace (4) screws and lightly tighten them.
Caution: Do not over tighten screws; frame may crack.
99044470A
Push to
turn ON
Push to
turn OFF
SmartSense
®
®
SCREWS
SCREWS
PADDLE / FRAME
ASSEMBLY
RESTORING POWER TO CONTROL
Control stores all settings in nonvolatile memory; so they
are not lost when power is removed. After power loss,
control will automatically return fan to its state (on or off)
before power was interrupted.
HOW TO RESTORE CONTROL FACTORY SETTINGS
This “Restore” procedure clears control’s nonvolatile
memory. It returns control to how it was shipped from
factory. All links are removed and any Feature selection is
turned off.
Links are unique for each device pair. If one end of the
link is removed, it is important to remove the other end.
“Restore” only removes links within the particular control.
Other link-end needs to be removed in other control.
CAUTION: Master must be “Restored” if any Slave control
is “Restored” or if any Slave control is removed from
System. Master and all Slave links must be reestablished
using “How To Link SmartSense
®
System” procedure.
1. Remove power from control’s “brain” by either: (a) turn
circuit breaker off or (b) pull SET button until it stays
extended by itself.
2. Wait 15-seconds.
3. Press and hold SET button.
4. For option (1a), turn circuit breaker on while SET button
is pressed. For option (1b), push in and press SET button
in one motion.
LED should be on while SET button is pressed.
5. Continue holding SET button for 3-seconds and then
release it.
LED should turn off.
WARRANTY
BROAN-NUTONE ONE YEAR LIMITED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from
the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, AND FUSES. This warranty does not cover (a) normal maintenance and service or (b) any products or
parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recom-
mended installation instructions.
The duration of an implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-
NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c) describe the
nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.
Broan-NuTone LLC Hartford, Wisconsin www.broan.com 800-558-1711