Filter
Top Products
RT2770
www.rcaaudiovideo.com
Congratulations on purchasing your new RCA unit.
Please read these instructions for quick tips on using the unit.
Setting up
1. Connecting the Speakers
• Six speakers are provided with the unit:
• 2 front speakers
• 1 center speaker
• 2 rear speakers
• 1 subwoofer.
• Speaker wires are color-coded to match the terminals.
• Connect the speaker wire to the corresponding color terminal as shown below.
• Press down the tab to open the terminal, insert the wire and release the tab.
• When connecting subwoofer, connect subwoofer control cable (red/black striped) at the back of the subwoofer to the subwoofer control jack on
the unit’s rear panel, then press POWER ON/OFF on the subwoofer speaker to turn it on.
SUBWOOFER
CONTROL
Remote Control
Tocom 56416640 (EN)
QuickStartGuide
2
3
4
9
12
15
19
1
5
6
7
8
10
11
14
13
16
17
18
Use this jack on
the rear panel to
connect to the
subwoofer
control cable
(red/black
striped) of the
subwoofer.
Use this jack on
the rear panel
to connect
another active
subwoofer
other than the
one supplied.
SUBWOOFER
AUDIO OUT
Center Speaker
Front Speakers
Right Left
Right Left
Rear speakers
(Surround Sound)
Subwoofer
White/grey or
black striped
Red/grey or
black striped
Green/grey or
black striped
Purple/grey or
black striped
Blue/grey or black striped
Grey/black striped
1.
Turn on/off the unit
2.
Directly access a preset station in
AM/FM mode
3.
Store station in AM/FM mode
4.
Select between Stereo and Mono
sound in FM mode
5.
Test the loudness of the speakers.
Refer to “Advanced Sound Control”
for details
6.
Select among night mode options
(DRC OFF, SOFT and ON) which
compresses the volume difference
between normal voices and sounds
such as explosions (Available only
during Dolby digital signal playback)
7.
Select among preset
equalizer mode (FLAT, POP, JAZZ,
ROCK, CLASSIC, BASS and TREBLE).
• Adjust bass or treble level
8.
Select among digital sound
processor (STEREO, HALL, CHURCH,
CLUB, STADIUM, STUDIO, 3 STEREO,
DOLBY PL EMULATION, DOLBY PL II
MUSIC and DOLBY PL II MOVIE)
9.
Enter setup mode
10.
Adjust the speakers’ distance
11.
Select among setting items in
setup mode
• Adjust the values when the display
shows the setup you want
to change
• Tune down or up the radio
frequency in AM/FM mode
12.
Mute all sound
13.
Select among subwoofer sound
level (SOFT SUBWOOFER, BALANCE
SUBWOOFER, STRONG SUBWOOFER
and POWERFUL SUBWOOFER)
14.
Adjust individual speaker volume.
Refer to “Advanced Sound Control”
for details
15.
Adjust the volume
16.
Select programmed stations in
AM/FM mode or directly access the
next or previous file in USB mode
17.
Start, stop or pause playback
(in USB mode only)
• Start reverse or forward accelerated
play(in USB mode only)
• Access MP3/WMA ID3 information
and current play time, current play
folder and track number,
play mode
• Access the repeat function
• Turn on/off random playback
• Enter Intro mode
18.
Enter sleep mode and selects sleep
time
19.Select audio sources
Press ON•OFF
Press the Number buttons
Press MEMORY
Press MONO/ST
Press TEST TONE
Press NIGHT
Press EQ
Press /
Press SURROUND
Press SETUP
Press DISTANCE
Press /
Press /
Press TUNER - and TUNER +
Press MUTE
Press SUBWOOFER
Press LEVEL
Press VOL + / VOL -
Press CH+ / CH-
Press PLAY, STOP or PAUSE to access the
relative functions.
Press REV or FWD
Press DISPLAY
Press REPEAT
Press RANDOM
Press INTRO
Press SLEEP
Press SOURCE buttons
RT2770 QSG EN 6/3/07 5:19 PM Page 2