Filter
Top Products
89
BREWING
90
SAFETY DEVICES
rature, close the knob and immediately clean the
spout with a damp cloth.
Attention: the spout is hot, it may cause burns!
Cappuccino
Through the special Cappuccinatore, this machine
can brew a real cappuccino without any problem.
By pressing the cappuccino button, these two
messages will be alternately displayed:
"CAPPUCCINO "
"READY FOR USE "
"SELECT FOR USE "
"READY FOR USE "
That is because the machine, as mentioned
before, can dispense two products at the same
time.
INCORPORATED SAFETY DEVICES
During the cappuccino dispensing, only the
programmed amount is dispensed if the
corresponding programming is enabled. On the
contrary, dispensing should be stopped by
pressing again the selection key when the desired
cappuccino amount has been reached.
To program the cappuccino amount, it is
necessary to keep the corresponding selection
key pressed till the desired amount is reached.
Attention: cappuccino amount can only
be programmed if the corresponding
programming function is enabled (see
page 83).
38
For cappuccino dispensing, fit suction pipe (26) of
the Cappuccinatore (25) in a milk container or in
another container. To prevent milk container
deformation, pierce it on the top to allow air entry.
Place the cup under dispenser (27) and press the
cappuccino selection key.
Cappuccino dispensing can be adjusted by turning
the special Cappuccinatore adjustment valve (28).
Note: it is suggested to use milk with low fat
amounts (1.5%).
Cappuccinatore cleaning
Let the Cappuccinatore drain a full water container
after each cappuccino dispensing: in this way,
the device will be perfectly cleaned.
Incorporated safety devices
Automatic off
Should the service door be open, the machine
automatically switches off. If the central unit is not
mounted, only water and steam can be
dispensed.
Electronic grinding time control
As soon as the coffee bean container is empty,
grinding automatically stops after 20 seconds
approx. Fill the container with coffee beans, as
shown at page 80.
Electronic pump control
The machine switches off automatically as soon
as the water in the tank is under the minimum level
checked by a special water level indicator (73).
Fill the tank according to the procedure shown at
page 80.
Electronic temperature adjustment
Said adjustment controls the correct temperature to
brew coffee and to dispense hot water and steam.
Coffee brewing is automatically interrupted should
the water temperature be excessive (safety
thermostat and overheating safety device
activated).
Antigravel device
Even selected coffees may contain impurities.
To avoid damages, the coffee grinder is fitted
with an antigravel device against impurities.
Should gravel end up into the coffee grinder, you
will hear a strong and characteristic noise. Stop
the machine immediately otherwise the machine
will automatically stop within 20 seconds thanks
coffee, coffee, small coffee) to obtain a cup of
coffee.
Important! This function does not allow the
double coffee cycle.
Dispensing may be interrupted by pressing one
of the coffee selection keys, if an excessive water
amount has been selected.
Hot water dispensing
Hot water dispensing is accomplished through
an independent water circuit which ensures the
correct temperature and supplies tasteless hot
water to be used for tea, soup, etc.
By operating the hot water key, the following two
messages will be displayed:
"HOT WATER "
"READY FOR USE "
"SELECT PRODUCT "
"READY FOR USE "
This happens because the machine, as mentioned
before, can dispense two products at the same
time.
During hot water dispensing, only the
programmed amount is dispensed if the
corresponding programming is enabled. On the
contrary, dispensing should be stopped by
pressing again the selection key when the desired
amount is reached.
If hot water only is dispensed, dispensing is faster
than when coffee is dispensed at the same time.
To program the hot water amount, it is necessary
to keep the corresponding selection key pressed
till the desired amount is reached.
Attention: hot water can only be
programmed if the corresponding
programming function is enabled (see
page 83).
During the programming phase, the following
message will be displayed:
"HOT WATER "
"PROGR. QUANTITY "
36
Place a glass or cup under the steam/hot water
spout (7), then press the hot water selection key.
Hot water will be automatically dispensed.
Steam dispensing
To heat milk or other drinks.
Always clean the spout with a damp cloth soon
after the use; otherwise, it might be difficult to
remove milk residues.
After a steam outflow, always drain the machine.
By turning steam knob (9), these two messages
will be displayed:
"STEAM "
"READY FOR USE "
"SELECT PRODUCT "
"READY FOR USE "
This happens because the machine, as mentioned
before, can dispense two products at the same
time.
Direct steam/hot water spout (7) on cup holder
grill (3) and slightly open knob (9), turning it
counterclockwise.
Wait until the remaining water has flown out of
the spout. Then, move the spout outwards and
plunge it deeply into the fluid to be heated.
37
Slowly open the steam/hot water knob and heat
the fluid, with a circular movement from the
bottom to the top.
When the fluid has reached the desired tempe-
USER MAINTENANCE
INSTRUCTIONS