Filter
Top Products
12
To minimize panel weight, you may use 2" (5.08 cm) spacer strips
around the perimeter in place of full-sheet solid spacer panels.
The spacer strips must be set in at least 1" (2.54 cm) from the
top, bottom and sides edges of the backer panel. If you use
spacer strips, it is also recommended that you use two 2"
(5.08 cm) strips horizontally centered for added support.
Stainless Steel Series Side Panels
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed at the end of a cabinet run. You
may choose an Inset, Flush, or Recessed Inset panel installation.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type
of installation you are planning.
NOTES:
■ The dimensions shown are actual product dimensions
and may not reflect the needed panel installation
dimensions.
■ The side panel should be a minimum of ½" (1.27 cm) thick
to avoid warping.
■ If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on rear wall.
Refrigerator
Top Grille
C
7
3
/
8
"
(18.73 cm)
8
1
/
2
"
(21.59 cm)
Bottom Offset
1" (2.54 cm)
F
Decorative Overlay Panels Backer Panels
Model A B C Model D E F
42" (106 cm) 17 ¹⁄₈"
(43.50 cm)
23 ¹⁄₈"
(58.74 cm)
41 ³⁄₈"
(105.09 cm)
42" (106 cm) 16 ¹⁵⁄₁₆"
(43.50 cm)
22 ¹⁵⁄₁₆"
(58.26 cm)
40 ¹⁄₂" (102.87
cm)
48" (122 cm) 19 ⁵⁄₈"
(49.85 cm)
26 ⁵⁄₈"
(67.63 cm)
47 ³⁄₈"
(120.33 cm)
48" (122 cm) 19 ⁷⁄₁₆" (49.37
cm)
26 ⁷⁄₁₆" (67.15
cm)
46 ¹⁄₂" (118.11
cm)
70
¹⁄₂
"
(179.07 cm)
70
¹⁄₂
"
(179.07 cm)
71
¹⁄₁₆
"
(180.50 cm)
24"
(60.96 cm)
34
³⁄₄
"
(88.27 cm)
E
D
Bottom Offset
¹⁄₈
" (3.2 mm)
Bottom Offset
¹⁄₈
" (3.2 mm)
B
Refrigerator
Freezer
Non-Dispenser
Freezer Frameless
Dispenser
Handle-Side
Offset
¹⁄₈
" (3.2 mm)
34
³⁄₈
"
(87.3 cm)
34
³⁄₈
"
(87.3 cm)
23
⁷⁄₁₆
"
(59.53 cm)
23
⁷⁄₁₆
"
(59.53 cm)
D
DD
Bottom Offset
¹⁄₈
" (3.2 mm)
A
A
71
¹⁄₁₆
"
(180.50 cm)
47
³⁄₁₆
"
(119.86 cm)
D
Bottom Offset
¹⁄₈
" (3.2 mm)
Freezer
Framed Dispenser
Handle-Side
Offset
¹⁄₈
" (3.2 mm)
A
A
Handle-Side
Offset
¹⁄₈
" (3.2 mm)
Handle-Side
Offset
¹⁄₈
" (3.2 mm)
Bottom Offset
¹⁄₈
" (3.2 mm)
12
⁵⁄₁₆
"
(31.27 cm)
24¹⁄₈"
(61.3 cm)
23
¹⁄₂"
(59.7 cm)
23¹¹⁄₁₆"
(60.3 cm)