Viking DGVU2004BSS Cooktop User Manual


 
16 17
Product Care
Product Care
Burner Head
If ports on burner head are clogged, clean with a straight pin. DO NOT
enlarge or distort the ports. DO NOT use a toothpick to clean the ports.
When replacing burner head, carefully align the 2 tabs underneath the
burner head with the outside edge of burner base. Make sure the tabs are
not aligned with the igniter and the burner cap is level.
Note: For stubborn stains, use a non abrasive cleanser such as Bon Ami™
and a soft brush or soft Scotch Brite™ pad.
Cleaning Tip: For difficult to clean burner caps and heads, place parts in a
zip seal bag with ammonia.
Burner Base
The base should be wiped regularly with hot soapy water at the end of
each cooling period. DO NOT use steel wool, abrasive cloths, cleanser, or
powders. To remove encrusted materials, soak the area with a hot towel to
loosen the material, then use a wooden nylon spatula. DO NOT use a
metal knife, spatula, or any other metal tool to scrape the aluminum base.
Wipe up any spills which remain on the sealed top surface.
Replace burner cap, burner head, and grates after drying thoroughly.
Cooktop Surfaces
Several different finishes have been used in your cooktop. Cleaning
instructions for each surface are given below. NEVER USE AMMONIA,
STEEL WOOL PADS OR ANY ABRASIVE CLOTHS AND MATERIALS SUCH
AS CLEANSERS, OVEN CLEANERS, OR ABRASIVE POWDERS. THEY CAN
PERMANENTLY DAMAGE YOUR COOKTOP.
Control Panel
DO NOT use any cleaners containing ammonia, abrasives, or stainless
steel cleaners on any surface that contains graphics. They could remove
the graphics from the control panel. Use hot, soapy water and a soft clean
cloth. DO NOT spray liquids directly onto control panel.
Control Knobs
MAKE SURE ALL THE CONTROL KNOBS POINT TO THE “OFF”
POSITION BEFORE REMOVING. Pull the knobs straight off. Wash in
detergent and warm water. Dry completely and replace by pushing firmly
onto stem. DO NOT use any cleaners containing ammonia or abrasives.
Cleaning and Maintenance
Stainless Steel Parts
Some stainless steel parts may have a protective wrap, which must be peeled
off. All stainless steel body parts should be wiped regularly with hot, soapy
water at the end of each cooling period and with liquid cleaner designed for
this material when soapy water will not do the job. If build-up occurs, DO NOT
use steel wool, or abrasive cloths, cleaners, or powders. If it is necessary to
scrape stainless steel surface to remove encrusted material, soak area with hot,
wet towels to loosen the material, then use a wooden or nylon spatula or
scraper. DO NOT use a metal knife, spatula, or any other metal tool to scrape
stainless steel surfaces. Scratches are almost impossible to remove. DO NOT
permit citrus or tomato juice to remain on stainless steel surface, as citric acid
will permanently discolor stainless steel. Wipe up any spills immediately
Brass Parts
All special ordered brass parts are coated with epoxy.
Burner Flames
Turn each burner on. Flames should be blue in color with no trace of
yellow. The burner flames should not flutter or blow away from the burner.
The inner cone of the flame should be between 1/2” and 3/4” long.
Cleaning and Maintenance
CAUTION
All special ordered brass parts are coated with an epoxy coating.
DO NOT USE BRASS CLEANERS OR ABRASIVE CLEANERS ON
ANY BRASS PARTS. All brass body parts should be wiped regularly
with hot soapy water. When hot soapy water will not do the job, use
every day household cleaners that are not abrasive.
COOKTOP
BURNER
Burner flames
-1/2” to 3/4”