Filter
Top Products
Record the following information indicated below. You will need it if
service is ever required. The serial number and model number for your
rangetop is located on the left rear side of the burner box.
Model Number Serial Number
Date of Purchase Date Installed
Dealer’s Name
Address
If service requires installation of parts, use only authorized parts to
ensure protection under the warranty.
PPlleeaassee rreettaaiinn tthhee mmaannuuaall ffoorr ffuuttuurree rreeffeerreennccee
SSeerrvviiccee IInnffoorrmmaattiioonn
If service is required after checking the troubleshooting guide:
1. Call your dealer or authorized service agency. The name of the
authorized service agency can be obtained from the dealer or
distributor in your area.
2. Have the following information readily available:
Model Number
Serial Number
Date of Purchase
Name of dealer from whom purchased
3. Clearly describe the problem that you are having.
If you are unable to obtain the name of an authorized service agency,
or if you continue to have service problems, contact Viking Range
Corporation at (888) 845-4641 or write to:
VVIIKKIINNGG RRAANNGGEE CCOORRPPOORRAATTIIOONN
PPRREEFFEERRRREEDD SSEERRVVIICCEE
111 Front Street
Greenwood, Mississippi (MS) 38930 USA
17
16
PPoowweerr FFaaiilluurree
DDuuee ttoo ssaaffeettyy ccoonnssiiddeerraattiioonnss
and the possibility of personal injury in
attempting to light and extinguish the burner, the grill should, under no
circumstances, be used during a power failure. The grill burner control
should always remain in the “OFF” position during a power failure.
Momentary power failure can occur unnoticed. The rangetop is
affected only when the power is interrupted. When it comes back on,
the rangetop will function properly without any adjustments. A
“brown-out” may or may not affect range operation, depending on
how severe the power loss is.
SSttaaiinnlleessss SStteeeell PPaarrttss
All stainless steel parts should be wiped regularly with hot, soapy water
at the end of each cooling period and with liquid stainless steel cleaner
when soapy water will not do the job.
DDoo nnoott uussee
steel wool, abrasive
cloths, abrasive cleaners, or powders. If necessary to scrap stainless
steel to remove encrusted materials, soak the area with hot towels to
loosen the material, then use a wooden or nylon spatula or scraper.
DDoo nnoott uussee aa mmeettaall kknniiffee,, ssppaattuullaa,, oorr aannyy ootthheerr mmeettaall ttooooll ttoo s
sccrraappee
ssttaaiinnlleessss sstteeeell.. FFoorr ooccccaassiioonnaall hheeaavvyy cclleeaanniinngg uussee,, aa cclleeaanneerr ssuucchh aass
LLiiqquuiidd ZZuudd ccaann bbee uusseedd
aaccccoorrddiinngg ttoo ppaacckkaaggee ddiirreeccttiioonnss.. DDoo nnoott
ppeerrmmiitt cciittrruuss oorr ttoommaattoo jjuuiiccee ttoo rreemmaaiinn oonn ssttaaiinnlleessss sstteeeell
ssuurrffaaccee,, aass
cciittrriicc aacciidd wwiillll ppeerrmmaanneennttllyy ddiissccoolloorr ssttaaiinnlleessss sstteeeell.. WWiippee uupp aannyy ssppiillllss
iimmmmeeddiiaatteellyy..
B
Brraassss PPaarrttss
CCAAUUTTIIOONN::
All brass special ordered parts are coated with an epoxy
coating.
DDOO NNOOTT UUSSEE BBRRAASSSS OORR AABBRRAASSIIVVEE CCLLEEAANNEERRSS OONN TTHHEE
BBRRAASSSS OOPPTTIIOONN PPAARRTTSS..
All brass parts should be wiped regularly with
hot soapy water.