Whirlpool 801 Dishwasher User Manual


 
Built-in opening
reaujrrements
Electrical Shock Hazard
Electrical wiring, water supply
line, and drain line must not
contact any exposed terminals of
the dishwasher wiring.
Cabinet opening must completely
enclose sides, top and back of
dishwasher.
Failure to follow these
instructions can result in death or
electrical shock.
Do Not run water or drain lines or
electrical wiring where they can
cross in front of or contact
dishwasher motor or legs.
Do Not install dishwasher over
carpeted flooring.
Do Not kink the power supply cable
between the dishwasher and
cabinet.
Protect dlshwasher and water lines
leadlng to dlshwasher against
freezlng. Damage from freezlng Is
not covered by the warranty.
Lorner
location -
2” (5.1 cm)
minimum
door to cabinet
or wall.
Cut openings -
Water line:
l/2” (1.3 cm)
;;gy;pe.
1 -l/2” (3.8
cm)
or lar
3
er hole.
Direc wiring:
;/df;l,(l.9
cm)
I-
Grommet
(Part No.
I
3027971
t1n
/
Unshaded area must be
free ot pipes, wires, and
drain hose. Electrical
outlet must be installed 4- 24”-
in an adjacent cabinet,
(61 cm)
it needed.
e 6” 6”
(15.2 cm)
(15.2 cm)
It-
required tar
electrical
‘ ‘;” ““I’,
cable hole
2-l/2”-
cut in metal
(6.4
cm) J
cabinet.
11
(a6Ycm)
min. trom
underside
Of
countertop
Llo”
(25.4 cm)
au
,” /(12.7cm)
zm)
(12.: cm)\r ‘t,
Proper electrical, drain and water
supply lines must be available or
must be installed, as specified,
within the shaded area. See
“Electrical requirements,” ‘Water
requirements,” and “Drain
requirements” sections.
Important: Observe all
governing codes and
ordinances.
It is recommended that the
electrical, drain and water supply
lines be located as close to the rear
wall as possible.
Check the locatlon where the
dishwasher will be installed. The
location must provide:
l
Easy access to water, electricity
and drainage lines.
l
Convenient loading - the best
location is to the left or right of the
kitchen sink.
l
Square opening for proper
dishwasher operation and
appearance.
l
Cabinet front that is perpendicular
to the floor.
l
Protection so that the water inlet
valve and drain cannot freeze.
l
l/4” (0.64 cm) minimum clearance
between the motor and the
flooring to prevent the motor from
overheating.
For installations where the dishwasher
will be left unused and subject to
freezing temperatures, see the
“Storing Your Dishwasher” or “Moving
or winterizing your dishwasher”
section of the dishwasher Use and
Care Guide.
Parts su Ifed
for insta ation:
‘pp
l
2 drain hose clamps
l
2 No.-10 x l/2” Phillips-head screws
l
drain hose
Remove parts from bag. Check that
all parts were supplied.
Tools and
materials required
for hstaIIation:
l
electric drill
l
Phillips screwdriver
l
2 adjustable wrenches
l
flat-blade screwdriver
l
measuring tape
l
pliers
l
pipe wrench
l
keyhole saw
l
90” elbow with 318” N.P.T.
external threads on one end. The
size of the other end must fit your
water supply line.
l
tubing cutter
l
pipe-joint compound
l
wire stripper and utility knife
l
5/16” and l/4” nut driver or hex
socket
l
3 twist-on wire connectors for
16.gauge wire
l gloves
l
safety glasses
Page 3