Whirlpool GZ5730 Ventilation Hood User Manual


 
7
19.
Remove both light socket
caps. Use pliers to grip the center
flanges of each cap, twist while
pulling down. Discard the caps.
Install (2) PAR20, 50W maximum
halogen bulbs or (2) R16, 40W
maximum incandescent bulbs.
Bulbs must be purchased
separately.
20.
Replace filters. Note: Filter
slot must be toward front of hood.
For non-vented recirculating
installations, make sure you have
installed the non-vented filters on
the back sides of the aluminum
mesh filters. (See Step 6.) Make
sure fan blade turns freely.
Fan: The 3-position rocker switch (on the left) controls the fan. The left
position is low speed, center position is off, and the right position is high
speed. An indicator light shows that the fan is on.
Light:The 3-position rocker switch (on the right) controls the lights. The
left position is low light intensity, center position is off, and the right
position is high light intensity.
21.
Turn power supply on and
check for proper operation.
center flange
of cap
Use and Care Information
WARNING — To reduce the risk of
fire or electrical shock, do not use
this fan with any solid-state speed
control device.
WARNING — TO REDUCE THE
RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO
PERSONS, OBSERVE THE
FOLLOWING:
Use this unit only in the manner
intended by the manufacturer. If
you have questions, contact the
manufacturer. Before servicing or
cleaning unit, switch power off at
service panel and lock switch
power off at service panel and lock
service panel to prevent power
from being switched on
accidentally. When the service
disconnecting means cannot be
locked, securely fasten a
prominent warning device such as
a tag to the service panel.
CAUTION: For general ventilating
use only. Do not use to exhaust
hazardous or explosive materials
and vapors.
WARNING — TO REDUCE THE
RISK OF A RANGE TOP GREASE
FIRE:
Never leave surface units
unattended at high settings.
Boilovers cause smoking and
greasy spillovers that may ignite.
Heat oils slowly on low or medium
settings.
Always turn hood ON when
cooking at high heat or when
cooking flaming foods.
Clean ventilating fans frequently.
Grease should not be allowed to
accumulate on fan or filter.
Use proper pan size. Always use
cookware appropriate for the size
of the surface element.
WARNING — TO REDUCE THE
RISK OF INJURY TO PERSONS
IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE
THE FOLLOWING:
SMOTHER FLAMES with a close-
fitting lid, cookie sheet, or metal
tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS.
If the flames do not go out
immediately, EVACUATE AND
CALL THE FIRE DEPARTMENT.
NEVER PICK UP A FLAMING
PAN — You may be burned.
DO NOT USE WATER, including
wet dishcloths or towels — a
violent steam explosion will result.
Use an extinguisher ONLY if:
You know you have a Class ABC
extinguisher, and you already know
how to operate it.
The fire is small and contained in
the area where it is started.
The fire department is being
called.
You can fight the fire with your
back to an exit.
LOW HIGH
FAN
LOW HIGH
LIGHT
Operation
To g et the most efficient
use from your new range
hood, read the “Use and
Care Information” section.
Keep your Whirlpool
Installation Instructions and
Use and Care Guide close
to range hood for easy
reference.
Replacing the
Halogen bulbs:
Before you begin, make sure that the range hood is turned off and that
the lamps have had sufficient time to cool. Halogen bulbs burn extremely
hot. See bulb packaging for further information.
Replace with (2) PAR20, 50W maximum halogen bulbs or (2) R16, 40W
maximum incandescent bulbs.