Filter
Top Products
Panel C
9.
To wire through top, mark a line 7-1/2" from
the right of the centerline on the underside
of the cabinet. Mark the point on this line
that is 1-3/8" from back wall. Drill a 1-1/4"
diameter hole through the cabinet at this
point. Note: If a cord-connection kit is used,
drill a 1-5/8" diameter hole.
8.
Determine and clearly mark a vertical
centerline on the wall and cabinet in the
area the vent opening will be made.
7-1/2"
centerline
7-1/2"
centerline
1-3/8"
7. Lift the range hood into final
position and center. Mark on the underside
of cabinet the location of the four keyhole
mounting slots. Set range hood aside on a
protected surface.
keyhole slot
front
of hood
To wire through rear, mark a line 7-1/2" from
the right of the centerline on the wall. Mark
the point on this line that is 1-3/8" from
underside of cabinet. Drill a 1-1/4"
diameter hole through wall at this point.
1-3/8"
from wall
(not cabinet
frame)
To vent through the roof with 3-1/4" x 10"
rectangular vent, mark a line 1" and 5" from
the back wall on the underside of the
cabinet. Mark lines 5-1/4" to the right and
left of the centerline on the underside of
cabinet that connect the lines just drawn.
Use a keyhole saw and saber saw to cut a
rectangular opening for the ventwork.
Repeat for the underside of the top of the
cabinet.
To vent through wall with 3-1/4" x 10"
rectangular vent, measure 1/8" and
3-5/8" down from underside of cabinet and
mark on back wall. Measure and mark a
line 5-1/4" to right and left of centerline,
connecting the two lines. Use a keyhole
saw and saber saw to cut a rectangular
opening for the ventwork.
10 .
To vent through the roof with 7" round vent,
mark 4-1/2" and 5" in from back wall along
the centerline on underside of cabinet. Use
these points as centers to draw 7-1/8"
circles on underside of cabinet. Use a saber
saw to cut the openings for the ventwork.
Repeat for the underside of the top of the
cabinet. This will create slotted openings
which makes it easier to install the vent
system.
cabinet
cutouts
4-1/2"
5"
7-1/8"
cabinet cutouts
1"
5-1/4"
5-1/4"
5"
Numbers correspond
to steps.
4.
7.
12.
14. 15.
5.
6. 16. 17.
7. 14. 15.
RH4900 Series
Shown
3.
15. 16.
keyhole slot
screw
11 .
Install vent system through the vent opening
in upper cabinet or wall. Complete venting
system according to method needed. See
“Venting requirements.” Use caulking to seal
exterior wall or roof opening.
12 .
Attach rectangular damper to selected
rectangular vent opening. If damper is
attached to back of range hood, be sure
damper hinge is toward the top. For round
vented installations, use round damper in
vent to prevent air from flowing back into
ventwork. If wall or roof cap has a damper,
remove damper blade from range hood.
13 .
Do Not turn on power until installation is
complete. Run wiring through wall or
cabinets according to the National Electrical
Code and local codes and ordinances.
14 .
Start screws through neck of each of the
four keyhole mounting screw slots marked
on the cabinet bottom.
round
damper
damper
15 .
Lift range hood into final position, feeding
electrical wire through wiring opening.
Position the range hood so that the large
end of the keyhole slots are over the screws.
Then push the hood toward the wall so that
the screws are in the neck of the slots.
Tighten mounting screws to cabinet, making
sure mounting screws are in narrow neck of
slots. Make sure that damper blade, if used,
rotates up and down freely.
Excessive Weight Hazard
Use two or more people to move and
install range hood.
Failure to follow this instruction can
result in back or other injury.
WARNING
centerline
centerline