Whirlpool TUD8750R Dishwasher User Manual


 
12
Canceling a Cycle
Anytime during a cycle, press CANCEL/DRAIN. Your dishwasher
starts a 2-minute drain, if needed, and clears all indicators. Let
the dishwasher drain completely.
NOTE: If your dishwasher does not need draining, the
dishwasher stops and clears all indicators.
To stop the drain
You can press CANCEL/DRAIN again to stop the drain
immediately. Remember to drain the dishwasher before starting a
new cycle.
To clear the indicators
Press CANCEL/DRAIN before starting the dishwasher to clear all
options and cycles.
Changing a Cycle or Setting
During the first fill of a cycle
1. Press a new cycle and/or options.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
3. Press START/RESUME.
After the first fill of a cycle
1. Press CANCEL/DRAIN. Your dishwasher starts a 2-minute
drain, if needed, and clears all indicators. Let the dishwasher
drain completely.
NOTE: If your dishwasher does not need draining, the
dishwasher stops and clears all indicators.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
3. Press a new cycle and/or options.
4. Press START/RESUME. (The door must be closed.)
Adding Items During a Cycle
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Lift up the door latch to stop the cycle. Wait for the spraying
action to stop before opening the door.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches.
4. Press START/RESUME. The dishwasher resumes the cycle
after a 5-second pause.
Option Selections
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn off the option,
or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can turn off the drying option anytime
before drying begins.
After a wash cycle, the dishwasher remembers the options used.
It uses the same options in the next wash cycle, if you press only
START/RESUME.
Hi-Temp Wash
Select this option to increase the target water temperature during
the wash portions of the cycle. Hi-Temp Wash raises the target
water temperature to 145ºF (63ºC) in the main wash. Heating the
water helps improve washing results. Hi-Temp Wash is useful
when loads contain baked-on food.
This option adds heat, wash time and water to the cycle.
NOTE: Hi-Temp Wash is an option with Pots & Pans and Normal
cycles.
Heated Dry
Select this option to dry dishes with heat.
Switching off Heated Dry skips the dry period. This is useful when
loads contain plastic dinnerware that may be sensitive to high
temperatures. The dishes take longer to dry, and some spotting
may occur. Some items (such as plastics) may need towel drying.
For best drying, use a liquid rinse aid.
NOTE: Heated Dry is an option with all cycles, except the Rinse
Only cycle. Heated Dry begins automatically with all cycles
unless you switch it off.
Lock
Use the lock to prevent unintended use of the dishwasher. You
can also use the lock feature to prevent unintended cycle or
option changes during a cycle.
When the lock is lit, all buttons are disabled.
NOTES:
The dishwasher door can be opened while the controls are
locked.
You can turn on the lock while the dishwasher is running. If
you open the door, unlock the controls and press START/
RESUME to restart. You can lock controls again, if desired.
To turn on the lock
Press and hold HEATED DRY for 4 seconds. The lock glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times and the selection is ignored.
To turn off the lock
Press and hold HEATED DRY for 4 seconds. The light turns off.