Filter
Top Products
Steps to Programming
2
YY
YY
Y
our Curtis Cafe System is Four Curtis Cafe System is F
our Curtis Cafe System is Four Curtis Cafe System is F
our Curtis Cafe System is F
actoractor
actoractor
actor
y Pre-Set for Optimum Py Pre-Set for Optimum P
y Pre-Set for Optimum Py Pre-Set for Optimum P
y Pre-Set for Optimum P
erformance.erformance.
erformance.erformance.
erformance.
Usually this Does Not Change. Usually this Does Not Change.
Usually this Does Not Change. Usually this Does Not Change.
Usually this Does Not Change.
Number of
Flashes
10%
20%
30%
40%
100%
1
2
3
4
10
Volume
Enter Program Mode – Enter Program Mode –
Enter Program Mode – Enter Program Mode –
Enter Program Mode – press and hold
STOP/WSTOP/W
STOP/WSTOP/W
STOP/W
ASHASH
ASHASH
ASH for about ten [10] seconds until all
lights start blinking.
TT
TT
T
o program Product % Rao program Product % Ra
o program Product % Rao program Product % Ra
o program Product % Ra
tio,tio,
tio,tio,
tio, press and hold the selected PUSH button for approximately
one second, then release. The current setting will be indicated by LED flashes.
TT
TT
T
o change the product throo change the product thro
o change the product throo change the product thro
o change the product thro
ww
ww
w
,,
,,
, press and hold the button until light starts quick flashing. Each quick flash increases
the amount by 10%. Release the button when the desired throw amount is achieved. After releasing the button, the
number of blinks represent the new setting.
TT
TT
T
o exit the Po exit the P
o exit the Po exit the P
o exit the P
oo
oo
o
wder Dispensing Mode,wder Dispensing Mode,
wder Dispensing Mode,wder Dispensing Mode,
wder Dispensing Mode, push the other PUSH button.
Enter
Program Mode
Enter
Product % Rati
o
Change
Product Throw
Exit
Program Mode
Product % RaProduct % Ra
Product % RaProduct % Ra
Product % Ra
tiotio
tiotio
tio
This controls the amount of dry product that is metered from the hoppers. This can be programmed from 10% to 100% of the capacity of
the dispensing system. By counting LED flashes you can determine the product % ratio currently set for this dispense button (see table).
PP
PP
P
ortion Control Liquid Dispensing Modeortion Control Liquid Dispensing Mode
ortion Control Liquid Dispensing Modeortion Control Liquid Dispensing Mode
ortion Control Liquid Dispensing Mode
This program adjustment allows you to setup the machine to automatically dispense a preset volume of coffee. When the user makes a
PUSH button selection, the SD2 unit dispenses only the volume of coffee programmed by the Portion Control Dispensing Mode. By setting
the unit for Portion Control Dispensing, you have locked out the manual dispense feature.
Enter Program Mode – Enter Program Mode –
Enter Program Mode – Enter Program Mode –
Enter Program Mode – press and hold
STOP/WSTOP/W
STOP/WSTOP/W
STOP/W
ASHASH
ASHASH
ASH for about ten [10] seconds until all lights start blinking.
TT
TT
T
o select & change the Po select & change the P
o select & change the Po select & change the P
o select & change the P
ortion Control Dispensing ortion Control Dispensing
ortion Control Dispensing ortion Control Dispensing
ortion Control Dispensing
VV
VV
V
olumeolume
olumeolume
olume – while in the programming mode, press and hold the
selected PUSH button until the liquid begins to flow, then release. The timing starts when liquid begins to flow.
Stop floStop flo
Stop floStop flo
Stop flo
w and Exit – w and Exit –
w and Exit – w and Exit –
w and Exit – When the desired volume is achieved, press this PUSH button once again to stop the
dispensing.
You have now set the timing for this button and have exited the programming mode. Pressing the selected
dispense button now will provide the liquid volume that you just set. To reset the timing, you must start again by
entering the programming mode.
Enter
Program Mode
S
elect & Chang
e
Preset Liquid
Dispense
Stop & Exit
WARNING HOT LIQUID, Scalding
may occur. Avoid splashing.
Place an empty container under the
dispensing nozzles while programming.
All programming is performed at the control
panel (illustration, right).
The Hot Water button is used for only for
dispensing hot water and does not require any
programming. Water is dispensed as long as the Hot Water button is held down.
The STOP/WASH BUTTON has several functions. This button is used to stop a Portion Control dispense cycle. It is used to wash out the
mixing and dispensing systems and it is used to enter programming functions.
COFFEE
DISPENSE
HOT WATER
DISPENSE
COFFEE
DISPENSE
STOP/WASH
BUTTON