Filter
Top Products
15
Oven Cavity
The enamelled oven cavity is best cleaned whilst the oven
is still warm.
Wipe the oven over with a soft cloth soaked in warm soapy
water after each use. From time to time it will be
necessary to do a more thorough cleaning, using a
proprietary oven cleaner.
If the soilage has become set, after the oven has cooled
down, the following process will help to soften the
splatters to help make cleaning easier.
1. Place the grill/ meat pan on the oven shelf positioned
in the lowest runner.
2. Add a few drops of wasing-up liquid to the pan and fill
to about 12 mm. with boiling water from the kettle.
3. Close the oven door, turn the oven function knob on fan
oven and set the thermostat knob on 50°C.
4. After 15 minutes, turn off the thermostat and allow the
fan oven to continue without heat for a further 5
minutes, when the temperature of the water will have
cooled down.
5. Carefully remove the pan of water from the oven and
use normal oven cleaners to clean away soil residues.
6. Leave a little of the soapy water to soak into any
burned on spillage on the floor of the oven for a longer
time if necessary.
Grease Filter (Fig. 12 - Page 3)
To prevent a build-up of fats on the fan impellor, the grease
filter must be fitted by clipping it over the vents in the back
panel.
To clean the grease filter
When the oven has cooled down, remove the filter by
pushing the protruding tongue on the filter upward, and
wash carefully.
The grease filter should be cleaned after every use. The
filter may be washed in a dishwasher on a 65°C wash. If
the filter is heavily soiled, place the filter in a saucepan of
water with approximately 1 teaspoon of automatic washing
powder or dishwasher powder. Bring to the boil and leave
to soak for approximately 30 minutes or longer depending
on the degree of soiling. Ensure the solution does not boil
over as it could mark your hob.
Rinse filter in clear water and dry.
Remember to refit the filter before using the oven again.
Replacing the Oven Light (Fig.13 - Page 4)
If the oven bulb needs replacing, it must comply with the
following specifications:
- Electric power: 25W,
- Electric rate: 230-240 V (50 Hz),
- Resistant to temperatures of 300°C,
- Connection type: E14.
These bulbs are available from your local Zanussi Force
Service Centre.
To replace the faulty bulb:
1. Ensure the oven is isolated from the electrical supply.
2. Turn the glass cover anticlockwise.
3. Remove the faulty bulb and replace with the new one.
4. Refit the glass cover.
5. Restore the electrical supply.
Oven Shelves
To clean the oven shelves, soak in warm soapy water and
remove stubborn marks with a well wetted soap
impregnated pad. Rinse well and dry with a soft cloth.
The shelf supports can be removed for easy cleaning (see
diagram). Please, ensure the retaining nuts are secure
when refitting the shelf support.
Cleaning the hinged grill (Fig.10 - Page 3)
This model has been fitted with a hinged grill element to
enable you to clean the roof of the oven easily.
Before proceeding ensure the oven is cool and
is isolated from the electricity supply.
1) Undo the screws which holds the grill in place (Fig.10
- Page 3). When doing this operation for the first time,
we recommend using a screwdriver.
2) Then gently pull the grill downward to allow access
to the oven roof.
3) Clean the oven roof with a suitable cleaner and wipe
dry before replacing the hinged grill element.
4) Gently push up the grill element into place and firmly
screw into place the holding nuts.
Ensure the grill holding nuts are firmly in place to
avoid the grill falling down when in use.