Filter
Top Products
13
1. Check that the baskets have been
loaded correctly and that the spray
arms can rotate freely
2. Turn on the water tap
3. Close the dishwasher door
4. Press the On/Off push button
The On/Off indicator light will come on.
5. Setting and starting the programme
Press the push button corresponding to the required
programme (see "Washing programmes" chart).
The indicator light corresponding to the programme and
the phase indicator lights foreseen for that programme will
illuminate.
After about 3 seconds from the last pressure of a push
button the programme starts automatically.
Once the programme has started the phase indicator
lights will turn off except for the phase under way.
Note: it is possible to select a washing programme also
with the door slightly opened.
In this case the start of the programme will occur after
about 3 seconds from the closure of the door.
a) Press On/Off push button.
b) Select a washing programme.
c) Close the door.
The programme will start automatically after about 3
seconds from the closure of the door.
6. To interrupt or cancel a washing
programme in progress
Interrupt or cancel a washing programme in progress
ONLY if it’s absolutely necessary.
Attention! Hot steam may escape when the door is
opened. Open the door carefully.
To interrupt a washing programme in
progress
a) Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the
point in which it was interrupted.
b) Press the On/Off push button (in this case all the
indicator lights turn off). Press the On/Off push button
again; the programme will start from the point in
which it was interrupted.
To cancel a washing programme in
progress
To cancel a washing programme you have to reset the
dishwasher; press simultaneously the function push
buttons 2 and 3 until all the push buttons indicator lights
will turn off (except for the On/Off indicator light) indicating
that the running programme has been cancelled.
If a new washing programme will be selected, check
that there is detergent in the detergent dispenser.
7. Setting/cancelling the "Delay start"
The setting of the delay start occurs before selecting
the programme.
Setting the "Delay start"
Press the "delay start" push button until the indicator light
corresponding to the chosen hours flashes (3, 6 or 9
hours).
Press the push button corresponding to the required
washing programme; the indicator light corresponding to
the programme illuminates and the phase indicator lights
for that programme start flashing.
From the moment that the washing programme has been
set, the delay start will begin with the countdown.
The countdown will decrease with step of 3 hours.
During the countdown, the indicator light of the selected
programme and the indicator light of the number of hours
to the start of the programme will remain illuminated.
Once the delay start has elapsed the programme will
start automatically, the indicator lights for delay start turn
off and the indicator light of the phase underway
illuminates.
Cancelling the "delay start"
It is possible to cancel a countdown in progress or before
it starts, simply pressing the delay start push button until
the indicator lights corresponding to the delay start hours
are off.
In this case the selected washing programme will start
automatically after 6 seconds.
8. End of the washing programme
The dishwasher will automatically stop and the end of
programme phase indicator light (END) will illuminate.
The indicator light of the programme just ended will
remain on.
If the door is not immediately opened at the end of the
programme, air will circulate inside the dishwasher to
prevent residual steam recondensing on the dishes as
water droplets.
This device operates intermittently for about 20 minutes,
as long as the dishwasher is switched on.
if the On/Off push button is pressed or the door is
opened during these 20 minutes, the device will be
automatically cancelled.
Switch off the dishwasher by pressing the On/Off push
button, the On/Off indicator light turns off.
Open the door and wait a few minutes before removing
the dishes; in this way they will be cooler and the drying
will be improved.
9. Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should
therefore be allowed to cool down before removing from
the appliance.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
Water may appear on the sides and the door of the
dishwasher as the stainless steel will eventually become
cooler than the dishes.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
Starting a washing programme