Filter
Top Products
Indicator lights: have the following meanings:
The salt and rinse aid indicator lights are never illuminated
while a washing programme is running even if filling with salt
and rinse aid is necessary.
Phase indicator lights: have the following meanings:
As soon as you select a washing programme, the phase
indicator lights for that programme will start flashing.
As the programme starts, the phase indicator lights turn off
except for the indicator light of the phase in progress which will
remain lit with a static light.
5
Salt refilling indicator light: illuminates when the salt
has run out and needs replenishing.
Rinse aid refilling indicator light: illuminates when
the rinse aid has run out and needs replenishing.
Wash: illuminates when the washing and rinsing
phases are running.
Drying: illuminates when the drying phase is
running.
End of cycle: illuminates when the washing
programme has ended.
It also has added functions of visual signalling as:
- the setting of the water softener,
- deactivation/activation of the dosage of rinse aid,
- intervention of an alarm due to the malfunction of
the machine.
Prior to using for the first time
Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections comply
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill
with dishwasher salt
5. Fill the rinse aid dispenser
The water softener
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these minerals and salts, the harder
your water is.
Water hardness is measured in equivalent scales, Clarke
degrees, French degrees and mmol/l (millimol per litre).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
The water softener must be set in both ways: manually, using
the water hardness dial and electronically, using the function
buttons on the control panel.
a) Setting manually
1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness dial to position 1 or 2 (see table).
4. Replace the lower basket.
The dishwasher is factory set
at position 2.
AA07
Clarke
degrees
°TH
(french degrees)
mmol/l
(millimol per litre,
international unit for the
hardness of water)
Range
manually electronically
64 - 88
53 - 63
46 - 52
36 - 45
28 - 35
23 - 27
18 - 22
13 - 17
5 - 12
< 5
9,0 - 12,5
7,6- 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
3,3 - 3,9
2,6 - 3,2
1,9 - 2,5
0,7 - 1,8
< 0,7
VI
VI
VI
VI
VI
III
III
II
I/II
I
91 - 125
76 - 90
65 - 75
51 - 64
40 - 50
33 - 39
26 - 32
19 - 25
7 - 18
< 7
2
2
2
2
2
2
1
1
1
1
level 10
level 9
level 8
level 7
level 6
level 5
level 4
level 3
level 2
level 1
yes
yes
yes
yes
yes
yes
yes
yes
yes
no
10
9
8
7
6
5
4
3
2
1
Water hardness
Adjusting the water
hardness setting
Number of
flashes of the
"End of cycle"
indicator light
Use
of salt