Filter
Top Products
1. Check that the baskets have been
loaded correctly and that the spray
arms can rotate freely
2. Turn on the water tap
3. Close the dishwasher door
4. Press the On/Off push button
The On/Off indicator light illuminates.
5. Setting and starting the programme
To select a programme, press the push button of the
programme you wish to select, the indicator light of the
programme push button illuminates and in the digital display
will appear, flashing, the running time (in minutes) of the
programme that has been set .
The phase indicator lights foreseen for that programme will
illuminate.
After about 3 seconds from the last pressure of a push
button the programme starts automatically.
In the digital display the running time of the programme is no
longer flashing and the indicator lights of the phases will turn
off except for the phase underway.
Setting and starting the programme with
"Care Plus" option
To select a programme, press the push button of the
programme you wish to select, the indicator light of the
programme push button illuminates and in the digital display
will appear, flashing, the running time (in minutes) of the
programme that has been set .
The phase indicator lights foreseen for that programme will
illuminate.
Within 3 seconds press the option push button for "Care
Plus". The indicator light of "Care Plus" push button
illuminates.
With the selection of the "Care Plus" option the temperature
in the last rinse phase will be held over 65°C for at least 10
minutes. Due to this, in the digital display the running time of
the selected programme will be updated.
Pressing the "Care Plus" push button switches the function
on or off. The indicator light of "Care Plus" push button shows
the current setting.
After about 3 seconds from the last pressure of a push
button the programme starts automatically.
In the digital display the running time of the programme is no
longer flashing and the indicator lights of the phases will turn
off except for the phase underway.
Note: it is possible to select a washing programme also
with the door slightly opened.
In this case the start of the programme will occur
automatically after the closure of the door. Until this moment it
is possible to change the setting made.
a) Press the On/Off push button.
b) Select a washing programme and if required the "Care
Plus" option.
c) Close the door.
6. To interrupt or cancel a washing
programme in progress
Interrupt or cancel a washing programme in progress
ONLY if it’s absolutely necessary.
Attention! Hot steam may escape when the door is opened.
Open the door carefully.
To interrupt a washing programme
a) Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the point
in which it was interrupted.
b) Press the On/Off push button (in this case all the indicator
lights turn off). Press the On/Off push button again; the
programme will start from the point in which it was
interrupted.
To cancel a washing programme
To cancel a washing programme you have to reset the
dishwasher; press simultaneously the function push buttons
2 and 3 for about 2 seconds, the indicator light of the running
programme starts flashing for about 2 seconds. After about 2
seconds all the indicator lights will turn off (except for the
On/Off indicator light and eventually the rinse aid and salt
indicator lights) indicating that the running programme has
been cancelled.
If a new washing programme will be selected, check that
there is detergent in the detergent dispenser.
7. End of the washing programme
The dishwasher will automatically stop.
The end of programme indicator light is illuminated.
In the digital display appears 0 (remaining programme time),
only in this case the programme has ended.
If the door is not immediately opened at the end of the
programme, air will circulate inside the dishwasher to prevent
residual steam recondensing on the dishes as water droplets.
This device operates intermittently for about 20
minutes, as long as the dishwasher is switched on.
If the On/Off push button is pressed or the door is opened
during these 20 minutes, the device will be automatically
cancelled.
Switch off the dishwasher by pressing the On/Off push
button.
Open the door and wait a few minutes before removing the
dishes; in this way they will be cooler and the drying will be
improved.
8. Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should
therefore be allowed to cool down before removing from the
appliance.
Empty the lower basket first and then the upper one; this will
avoid water dripping from the upper basket onto the dishes in
the lower one.
Water may appear on the sides and the door of the
dishwasher as the stainless steel will eventually become
cooler than the dishes.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
Starting a washing programme
14
"Care Plus" Option activated
indicator light on
"Care Plus" Option deactivated
indicator light off (factory setting)