-
-
-
I
I
I
N
N
N
S
S
S
T
T
T
A
A
A
L
L
L
L
L
L
A
A
A
T
T
T
I
I
I
O
O
O
N
N
N
M
M
M
A
A
A
N
N
N
U
U
U
A
A
A
L
L
L
-
-
-
34
Parameter Description
Default
(BCF...)
Default
(BC...)
min MAX
I.F.R.
B01 Room thermostating temperature in the first phase -48°F -13°F -58°F 122°F
B02 Under surface T control start temperature
41°F 86°F -58°F 210°F
B03 First coefficient of the control relation
0 -2 -50 50
B04 Second coefficient of the control relation
0 16 -50 50
B05 Third coefficient of the control relation
-8 -8 -50 50
B06 Under surface T initial value determining the end of the first phase
30°F 34°F -58°F 210°F
B07 Phase two formula coefficient
99 10 0 99
B09 Under surface t min. value allowed during the third phase
32°F 30°F -58°F 210°F
B10 End of intelligent quick cooling core temperature
46°F 38°F -58°F 210°F
B11
Delay from the positive result of the needle test for starting the
procedure to determine the end of the first phase
60 sec 60 sec 0 sec 99 sec
B12 First phase temperature detection time
30 sec 30 sec 0 sec 99 sec
B13 First phase min. duration
6 min 6 min 0 min 99min
B16 Defrost on starting intell. QC cycle (0=no 1=yes)
0 0 0 1
B17 Inhibition temperature
194°F 176°F -58°F 210°F
B18
Room Set point in the event of automatic switch to time or
temperature mode
19°F 32°F -58°F 210°F
B19 Max. duration possibile for intelligent QC process
999 min 150 min 1 min 999 min
B20
Under surface T safety value determining the end of the first
phase
30°F 38°F -58°F 210°F
B21 First coefficient of the room thermostating curve (third phase)
10 -25 -90 99
B22
Second coefficient of the room thermostating curve (third
phase)
-50 -28 -90 99
B23
Storing activation at the end of intell. QC cycle
(0 = no; 1 = yes)
1 1 0 1
B24 Room thermostat Set-point in storing
36°F 36°F -130°F 194°F
B26 Core temperature limit for the timer start
999 0 0 999
B27 Adjuster of fans speed in the third phase
99 0 0 99
B28 Cold pulse adjuster
10 0 0 99
COMMUNICATION
ADD Device Address 1 1 1 147
SC
Serial Control :
0 = not activated
1 = print
2 = ModBus
1
1
0
2
MB1 BaudRate: 0 = 2400; 1 = 4800; 2 = 9600; 3 = 18200
2 2 0 3
MB2 Parity: 0 = no parity; 1 = odd; 2 = even
2 2 0 2
TYPE OF CYCLE
G01
Positive QC cycles only :
0 = Positive and Negative
1 = Positive only
0 0 0 1
CHANGING PARAMETERS
Press menu/esc to select the desired menu
Use the keys up and down to display
Press enter to confirm your choice.
The display shows
(only the 1st time)
ervice
sc
ervice
Password 0
