Cleaning the milk frother with the CLEAN button
Important! Danger di scottature
When cleaning the internal tubes of the milk container, a little
hot water leaks out of the frothed milk tube (B5).
Avoid contact with splashes of water.
“Press CLEAN button” ashes on the display each time you
use a milk function. To eliminate all milk residues, proceed as
follows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Press the “CLEAN” button (g. 23) and keep pressing until
the progress bar which appears on the display together
with the message “Cleaning underway” is complete;
4. Remove the milk container and always clean the nozzle
with a sponge (g. 24).
Please note!
• When“PressCLEANbutton”ashesonthedisplay,you
can still prepare any type of coee or milk. If you have to
make a number of drinks with milk, wait until you have
delivered the last cup before cleaning the container.
• The milk left in the container can be kept in the
refrigerator.
• Insomecases,tocleanyoumustwaitfortheapplianceto
heat up, holding the CLEAN button down.
Programming the quantities of coee and milk in the
cup
The appliance is set by default to automatically deliver standard
quantities.
To change these quantities, proceed as follows:
1. Place a cup under the coee spouts and milk spout.
2. Press the CAPPUCCINO button and hold down for at
least 8 seconds until the message “Milk for CAPPUCCINO
Program Quantity” is displayed.
3. Release the button. The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the CAPPUCCINO button again.
5. After a few seconds, the appliance starts delivering coee
into the cup and the message “Coee f. CAPPUCCINO
Program Quantity” is displayed.
6. Once the required quantity of coee has been delivered
into the cup, press the CAPPUCCINO button. Coee
delivery stops.
The machine is now reprogrammed with the new quantities.
HEATING WATER
Please note:
A few seconds may elapse between “Energy saving” mode and
delivery of hot water; “Preparation underway...” is displayed.
Preparation
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water.
The hot water spout becomes hot while water is being delivered
and must be handled by the handle only.
1. Make sure the hot water spout is attached correctly
2. Place a container under the water spout (as close as
possible to avoid splashes) (g. 4).
3. Press the button The message “Hot Water” is
displayed.
4. Water ows out of the spout. Delivery stops automatically
after about 250 ml.
5. To interrupt delivery of hot water manually, press the
button again.
Change the quantity of water delivered automatically.
The appliance is set by default to automatically deliver 250ml.
To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press the button until the message “Hot Water
Program Quantity” is displayed.
3. When the hot water in the cup reaches the required level,
press the button again.
The machine is now reprogrammed with the new quantity.
CLEANING
Important!
• Do notuse solvents, abrasive detergents oralcoholto
clean the appliance. With De’Longhi superautomatic
coee makers, you need not use chemical products to
clean the machine.
• None of the components can be washed in a dishwasher
apart from the milk container (B).
• Donotusemetalobjectstoremoveencrustationsorcoee
deposits as they could scratch metal or plastic surfaces.
Cleaning the coee maker
The following parts of the machine must be cleaned regularly:
- coee grounds container (A15),
- drip tray (A13),
- the inside of the machine, accessible after opening the
service door (A14),
- water tank (A10),
- coee spouts (A16) and hot water nozzle (A9),
- pre-ground coee funnel (A7),
- infuser (A18)
- milk container (B).
Cleaning the coee grounds container
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coee cannot be made.
1. Open the service door on the front of the appliance (g.
25), extract the drip tray (g. 26), empty and clean.
2. Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
3. Replace the drip tray complete with grounds container.
4. Close the service door.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds. If this is not done,
when you make the next coees, the grounds container may
ll up more than expected and clog the machine.
Cleaning the drip tray
Important!
If the drip tray is not emptied regularly, the water could overow
from the edge and seep inside or around the machine.
This could damage the machine, the surface it rests on or the
surrounding area.
The drip tray is tted with a level indicator (red) showing the
level of water it contains (g. 26).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the drip tray:
1. Open the service door (g. 25);
2. Remove the drip tray and the grounds container (g. 26);
3. Empty the drip tray and grounds container and wash
them;
4. Replace the drip tray complete with grounds container;
5. Close the service door.
Cleaning the inside of the machine
Danger of electric shock!
Before cleaning internal parts, the machine must be turned
o (see “Turning o”, page 10) and unplugged from the mains
power supply.
