
68-974-50
Rev A
04 11
4
Selected SIS Commands
The table below shows a partial list of SIS commands the you can use for operation and configuration of the GSS. For a complete
listing, see the GSS 100 User Guide. Run the following commands from a PC connected to the RS-232 port (item
e
on page 1).
Command
ASCII Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Recall an image to buffer
EX!
RF
}
Cim
•
X!]
Select image
X!
(file name with extension [*.bmp or *.jpg]) to display.
NOTE: It will take several seconds between the issuance of the recall command (
EX!
RF
}
) and the receipt of the Cim response.
Take
%
Tke
]
Swap the displayed and buffered images using the selected effect
(cut or dissolve).
Switch effect
9*
X@
# Eff
X@] X@
: 0 = cut 1= dissolve.
Dissolve duration
10*
X#
# Dur
X#]
Set the duration of the dissolve effect to
X#
, in 0.1-second increments.
Display source
X$
! Chn
X$] X$
: 0 = last store image 1= pass-thru
Slide show interval
2*
X%
# Sli
X%]
Set the display time for each image to
X%
seconds.
Pass-through configuration
1*
X^
# Pas
X^] X^
: 0 = pass-thru 1= no pass-thru
Auto-switch and slide show mode
4*
X&
# Aut
X&]
Set auto-switch and slide show mode.
X&
definitions:
X&
: 0 = off 2 = on/still
1 = off/show 3 = on/show
Stored image output rate
X*
*
X^
= Rte
X*
*
X(]
Set the output resolution for the stored image to
X*
at
X(
Hz.
See below for
X*
and
X(
definitions.
Stored image output sync format
6*
X1)
# Syn
X1)]
Set the output sync format of the stored image to
X1)
.
X1)
: 0 = RGBHV 1 = RGBS
Stored image output sync polarity
7*
X1!
# Pol
X1!]
Set the output sync polarity of the stored image to
X1!
.
X1!
: 0 =
H– / V– 2 = H+ / V–
1 = H– / V+ 3 = H+ / V+
RGB delay
8*
X1@
# Dly
X1@]
Mute the RGB output for
X1@
(in 0.1-second increments) before
displaying the RGB pass-through input.
Video mute and unmute
X1#
B Vmt
X1#] X1#
: 0 = unmute 1= mute
Front panel locks and unlock
(executive mode)
X1$
X Exe
X1$] X1$
: 0 = unlock 2 = complete lock
1 = partial lock
X*
= Resolution 0 = 640 x 480 5 = 1024 x 1024 10 = 1365 x 768 15 = 720p
1 = 600 x 600 6 = 1280 x 768 11 = 1365 x 1024 16 = 1080i
2 = 852 x 480 7 = 1280 x 1024 12 = 1400 x 1050 17 = 1080p
3 = 1024 x 768 8 = 1360 x 765 13 = 480p 18 = 1280 x 800
4 = 1024 x 852 9 = 1365 x 768 14 = 576p 19 = 1440 x 900
X(
= Refresh rate 0 = 50 Hz 3 = 96 Hz
1 = 60 Hz 4 = 100 Hz
2 = 72 Hz 5 = 120 Hz
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada
Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada
Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2011 Extron Electronics. All rights reserved. www.extron.com
GSS 100 • Setup Guide