Note
Particles may accumulate in the IceMaker or water line
the first time the appliance is used or after an extended
period out of service.
u
To achieve this, do not consume or use the ice cubes
that are produced within 72 hours.
5.16.3 Setting the water supply time
The opening time of the valve on the IceMaker can be
adjusted if, for example, the water pressure in the pipe is
too low or too high.
The water supply time can be set in stages from E1 (short
supply time) to E8 (long supply time). The default setting
is E3.
u
Activate setting mode: press and hold the SuperFrost
button
Fig. 2 (9)
for approximately 5 s.
w
S is shown on the display.
w
The Menu symbol
Fig. 2 (3)
lights up.
u
Using the Up button
Fig. 2 (1)
or Down button
Fig. 2 (2)
,
select E.
u
To confirm: briefly press the SuperFrost button
Fig. 2 (9)
.
u
To increase the water supply time: press the
Up button
Fig. 2 (1)
.
u
To decrease the water supply time: press the
Down button
Fig. 2 (2)
.
u
To confirm: press the SuperFrost button
Fig. 2 (9)
.
u
Deactivate setting mode: press the On/Off button
Fig. 2 (8)
.
-or-
u
Wait 5 mins.
w
The temperature is again displayed on the temperature
display.
5.16.4 Switching off the IceMaker
When the IceMaker is switched off, the drawer of the
IceMaker can also be used for freezing and storing food.
u
Press the On/Off button for about 1 second until the
LED goes out.
u
Clean the IceMaker.
w
This ensures that no water or ice remains in the
IceMaker.
6 Maintenance
6.1 Replacing the water filter
The water filter should be changed when the Filter symbol
Fig. 2 (5)
lights up. It should be replaced every six months
at least or whenever you notice a significant decrease in
the flow rate You can order one from your dealer or by
visiting our web site at www.liebherr-appliances.com.
The used water filter contains activated carbon and can
be disposed of with normal household waste.
To remove the old water filter:
Fig. 5
u
lift the ventilation grid
Fig. 5 (1)
up and pull out.
u
Open the filter change flap
Fig. 5 (2)
.
u
Pull the water filter carriage
Fig. 5 (3)
out.
u
Remove the filter cover
Fig. 5 (6)
.
u
Catch any dripping water with your hand or with a dish.
u
Turn the water filter
Fig. 5 (3)
about 100° anti-clockwise
and pull out.
Note
If no new water filter is inserted:
u
put the filter cover on to protect the filter unit from dirt
and dust.
To install a new water filter:
Fig. 6
u
Insert the new filter
Fig. 6 (4)
and turn it about 100°
clockwise as far as it will go.
u
Place the cover
Fig. 6 (6)
on the filter.
u
Write the date of the next filter replacement on the
supplied adhesive label
Fig. 6 (5)
and affix it to the filter
cover
Fig. 6 (6)
.
u
Push in the water filter carriage
Fig. 6 (4)
.
u
Close the filter change flap
Fig. 6 (3)
.
u
Fit the ventilation grid
Fig. 6 (1)
again and push down. It
must close flush with the floor.
Note
New water filters may contain particulate matter.
u
Do not consume or use ice cubes produced within 72
hours after replacing the filter.
u
Remove any ice still present in the IceMaker tray. You
can keep this ice in another tray for later use.
u
Make sure the filter does not leak and no water is
coming out.
To reset the timer:
u
Select setting mode: Press and hold the SuperFrost
button
Fig. 2 (9)
for approx. 5 seconds.
Maintenance
* Depending on model and options 11
