3
Controls and Connectors .................................. 3
Dimensions ........................................................ 3
AC Power ........................................................... 4
Audio Input ........................................................ 5
Limiting and Protection Circuitry ..................... 6
Rigging ............................................................... 7
Complete Systems .............................................. 8
Verifying Polarity ............................................... 10
Coverage Angles and Polar Plots..................... 11
Array Design ...................................................... 14
Safety Summary................................................ 15
Specifications .................................................... 16
Contents
ATENCIÓN
:
ACCESO INTE
AUTORIZADO A PERSONAL
ACHTUNG
:
GEHÄUSE NIC
UND REPARATUR NUR DURC
ATTENTION
:
ENTRETIEN
INTERNES NE SONT AUTORI
PERSONNEL TECHNIQUE QU
UK WARNING
:
THIS APPA
NO OPERATOR SERVICEABLE
REFER SERVICING TO QUALIFI
WARNINGS:
THIS PRODUCT M
This surface may reach high t
To ensure proper operation, allo
clearance from this surface and
To reduce the risk of electric sh
No operator serviceable parts in
Refer servicing to qualified pers
To reduce the risk of fire or elec
do not expose this appliance to
!
Meyer Sound, B
1
2
3
1
3
2
Loop
Input
PUSH
Network
Service
Wink
Reset
Activity
Remote Monitor System
10A RMS
20A Peak
88-127V
~
50-60Hz
700W RMS MAX
Operational voltag
Turn on 80V
~
T
Turn on 160V
~
T
Auto-Voltage Sele
P
U
S
H
R
E
-
C
I
R
K
-
I
T
P
U
S
H
R
E
-
C
I
R
K
-
I
T
Controls and Connectors
European Rear User Panel
with IEC 309 connector
Dimensions
15.25"
13.55"
21.0"
20.5"
2.0"
9.55"
30.0"
21.0"
Front Side Top
All units in inches
20.50"
9.55"
14.26"
2.0"
Rear User Panel shown with the optional
Remote Monitoring System (RMS) panel
ATENCIÓN
:
ACCESO INTERNO SOLO
AUTORIZADO A PERSONAL TÉCNICO CALIFICADO
ACHTUNG
:
GEHÄUSE NICHT ÖFFNEN WARTUNG
UND REPARATUR NUR DURCH ELEKTROFACHKRÄFTE
ATTENTION
:
ENTRETIEN ET REPARATIONS
INTERNES NE SONT AUTORISEES QU'AU
PERSONNEL TECHNIQUE QUALIFIÉ
UK WARNING
:
THIS APPARATUS MUST BE EARTHED.
NO OPERATOR SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL
WARNINGS:
THIS PRODUCT MUST BE GROUNDED
This surface may reach high temperatures while in use.
To ensure proper operation, allow at least 6 inches
clearance from this surface and adequate ventilation.
To reduce the risk of electric shock do not remove cover.
No operator serviceable parts inside.
Refer servicing to qualified personnel.
To reduce the risk of fire or electric shock
do not expose this appliance to rain or moisture.
!
Meyer Sound, Berkeley, CA. USA
1
2
3
1
3
2
Loop
Input
PUSH
Active / Speaker Fault
2 +
3 +
10K
Ω
Balanced
Input Polarity
LO Limit
HI Limit
Network
Service
Wink
Reset
Activity
Remote Monitoring System
CQ
Earth / Chassis
1
Case
220K
Ω
ESD
P
U
S
H
R
E
-
C
I
R
K
-
I
T
P
U
S
H
R
E
-
C
I
R
K
-
I
T
Mains circuit
breakers
Signal input and
loop connectors
Power LED (green/red)
Input polarity switch
Low Limit (red)
High Limit (red)
Tie-wrap anchor
Mains AC inlet
Remote Monitoring
System panel
(if RMS is installed)
95-125V
~
50-60Hz
1400W RMS MAX
208-235V
~
50-60Hz
1400W RMS MAX
Auto-Voltage Select
