Filter
Top Products
9
Using Electronic Oven Control (some models only)
Manual Time Entry
To cook food using a specific entered time and power level.
NOTE: To use Time Entry, you must press POWER LEVEL Pad first.
1. Open oven door and place food in oven. Close door.
• :0 displays. Light will turn on.
2. Press POWER LEVEL pad.
• Press POWER LEVEL pad to change power level if desired
(some models).
• Power level (example: 100%) displays.
- 100% indicates 100% microwave power, 80% indicates 80%, 60%
indicates 60%, and 40% indicates 40% microwave power. By
continuing to press the Power level pad, the power level will cycle
through each level continuously.
3. Enter cooking time by using the numbered pads.
4. Press START/+30 SEC pad to begin cooking cycle.
• At end of cooking cycle, oven beeps and shuts off.
Programmed Pads
To cook food using pads preprogrammed with cooking sequences.
1. Open oven door and place food in oven. Close door.
• :0 displays. Light will turn on.
2. Press desired pad.
• For single pad entry, press only one pad.
• For double pad entry, press
same pad twice.
• If pad has not been
programmed, NO DATA displays.
3. Oven begins to cook.
• Total cooking time displays.
4. At end of cooking cycle oven beeps and shuts off.
Factory Settings
Pad Time Pad Time
1
10 sec.
6
1 min. 30 sec.
2 20 sec. 7 2 min.
3
30 sec.
8
3 min.
4 45 sec. 9 4 min.
5
1 min.
0
5 min.
QTY 2X Pad
(some models)
To double the cooking time temporarily
when cooking more than one serving. The
maximum cooking time is 60 minutes 00
seconds except for full power. Full power
(100%) maximum cooking time is 20 minutes
00 seconds.
1. Open oven door and place food in
oven. Close door.
• :0 displays. Light will turn on.
2. Press QTY 2X pad.
• DOUBLE displays
3. Press desired preprogrammed pad or
pad sequence. (example: pad 5)
• PROG-05 displays
4. After 1 second, oven begins cooking.
Displayed cooking time is the total of
original cooking time doubled.
Interrupting
Operation
Open oven door or press STOP/RESET pad
to interrupt operation. Display continues to
show countdown time. Close door and
press START/+30 SEC pad to resume oven
operation.
Do I
have
stage
programming?
Stage programming is a hidden
feature—it is not shown with a pad on the
oven. Stage cooking is a feature that is
present when programming. See the
Programmed Pads section on this page for
details.
STOP/
RESET
QTY
2X
Defrost Pad
Defrosts food by dividing total defrost time into periods of alternating defrost and stand times by cycling on and off:
1. Open oven door and place food in oven. Close door.
2. Press DEFROST pad.
• DEFROST indicator lights and :0 shows in the display.
3. Press the number pad(s) to enter the desired defrosting time.
4. Press START/+30 SEC pad.
5. Oven begins to cycle.
• The display counts down the time to show you how much defrosting time is left in the DEFROST mode.
NOTE: Oven beeps during the defrosting cycle to signal that the food needs to be turned or rearranged.
6. Open door and rearrange food. Close door.
7. Press START/+30 SEC pad to continue defrost cycle.
NOTE: If you don’t open door to rearrange food, defrost cycle continues.
DEFROST
POWER
LEVEL
START/
+30 SEC
17
7
11
1
11
1
Canceling
Mistakes
If oven is not cooking, press STOP/
RESET pad to clear display. If oven is
cooking, press STOP/RESET pad once
to stop oven, then again to clear display.
If oven door is open and time shows in
display, close oven door and press
STOP/RESET pad to clear display.
STOP/
RESET