Filter
Top Products
Chapter 6 Advanced 266 Front-Side Bus AMD Athlon™ XP Processor Model 8 Specifications 23
25175H—March 2003 AMD Athlon™ XP Processor Model 8 Data Sheet
Preliminary Information
Table 2 shows the part-specific electrical and thermal
specifications in the C0 working state and the S1 Stop Grant
state for processors with a CPUID = 681
Table 2. Electrical and Thermal Specifications for Processors with a CPUID of 681
Frequency in MHz
(Model Number)
V
CC_CORE
(Core
Voltage)
I
CC
(Processor Current)
Thermal Power
5
Maximum Die
Temperature
Working State C0
Stop Grant S1
1, 2, 3, 4
Maximum Typical Maximum Typical Maximum Typical
1400 (1600+)
1.60 V 30.3 A 27.5 A 8.1 A 4.9 A 48.5 W 44.0 W
90°C
1467 (1700+)
1.50 V 32.9 A 29.9 A 5.4 A 3.9 A 49.4 W 44.9 W
1.60 V 30.9 A 28.0 A 8.1 A 4.9 A 49.4 W 44.9 W
1533 (1800+)
1.50 V 34.0 A 30.9 A 5.4 A 3.9 A 51.0 W 46.3 W
1.60 V 31.9 A 28.9 A 8.1 A 4.9 A 51.0 W 46.3 W
1667 (2000+)
1.60 V 37.7 A 34.2 A 8.1 A 4.9 A 60.3 W 54.7 W
1733 (2100+)
1.60 V 38.8 A 34.9 A 8.1 A 4.9 A 62.1 W 55.9 W
1800 (2200+)
1.60 V 39.3 A 35.6 A 8.1 A 4.9 A 62.8 W 57.0 W
85°C
2000 (2400+)
1.65 V 41.4 A 37.6 A 8.9 A 5.4 A 68.3 W 62.0 W
2133 (2600+)
1.65 V 41.4 A 37.6 A 8.9 A 5.4 A 68.3 W 62.0 W
Notes:
1. See Figure 3, "AMD Athlon™ XP Processor Model 8 Power Management States" on page 9.
2. The maximum Stop Grant currents are absolute worst case currents for parts that may yield from the worst case corner of the
process and are not representative of the typical Stop Grant current that is currently about one-third of the maximum specified
current.
3. These currents occur when the AMD Athlon™ system bus is disconnected and has a low power ratio of 1/8 for Stop Grant
disconnect and a low power ratio of 1/8 Halt disconnect applied to the core clock grid of the processor as dictated by a value of
2003_1223h programmed into the Clock Control (CLK_Ctl) MSR. For more information, refer to the AMD Athlon™ and
AMD Duron™ Processors BIOS, Software, and Debug Developers Guide, order# 21656.
4. The Stop Grant current consumption is characterized at 50°C and not tested.
5. Thermal design power represents the maximum sustained power dissipated while executing publicly-available software or
instruction sequences under normal system operation at nominal V
CC_CORE
. Thermal solutions must monitor the temperature of
the processor to prevent the processor from exceeding its maximum die temperature.