Ariston LFF 8M5 Dishwasher User Manual


 
EN
12
Rinse aid and refined salt
Only use products which have been specifically designed
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard.
(Follow the instructions given on the packaging).
If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID indicator lights will stay lit.
Measuring out the rinse aid
Rinseaidmakesiteasierforthecrockerytodry,aswaterruns
off surfaces more readily and therefore does not leave streaks
or marks.
The rinse aid dispenser should be filled:
•WhentheLOWRINSEAID* indicator light on the control
panel is illuminated;
1.Openthedispenserbyturning
the lid (G) in an anticlockwise
direction.
2. Pour in the rinse aid, making
sure it does not overflow from the
dispenser. If this happens, clean
the spill immediately with a dry
cloth.
3. Screw the lid back on.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
mayadjustthequantityofrinseaidused.Useascrewdriverto
turn the dosage adjuster (F) to one of the 6 pre-set positions
(the default position is set to 4):
•Iftherearestreaksonthecrockery,settheadjustmentdevice
toalowernumber(1-3).
•Ifdropsofwaterremainonthecrockeryoriftherearelimescale
marks present after the cycle has finished, set the adjuster to
a higher number (4-6).
Setting the water hardness
Everydishwasherisequippedwithawatersoftenerwhich,by
using refined salt designed especially for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the wa-
ter hardness level in your area. This information can be obtained
from the organisation which supplies your household with water.
- Switch on the appliance by pressing the ON/OFF button.
- Press the P button and hold for a few seconds; two short beeps
will sound and the wash cycle indicator light corresponding to
the set degree of hardness will flash slowly on the control panel
(the water softening system is set to number 3).
- Press the P button repeatedly until the desired hardness level
has been reached
(1-2-3-4-5*seeWaterhardnesstable)
.
E.g.Hardnesslevel1(1
st
wash cycle indicator light flashes)
Hardnesslevel 2(1
st
wash cycleindicatorlight on,2
nd
wash
cycle indicator light flashes)
Hardnesslevel 3(1
st
and2
nd
wash cycle indicator lights on,
3
rd
wash cycle indicator light flashes etc.) up to a maximum of
level 5*.
-Toexitthefunction,waitapproximately30secondsorswitch
off the machine using the ON/OFF button.
Evenifusingmulti-functionaltablets,thesaltdispensershould
still be filled.
Evenifusingmulti-functionaltablets,thesaltdispensershould
still be filled.
(°dH=hardnessmeasuredinGermandegrees-°f=hardness
measuredinFrenchdegrees–mmol/l=millimolesperlitre)
Measuring out the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refinedsaltremoveslimescalefromthewater,thusavoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
• Whenthegreenfloat* cannot be seen by simply looking at
the cap of the salt dispenser;
• WhentheLOWRINSEAIDindicatorlightonthecontrolpanel
is illuminated *;
1.Removethelowerrackandunscrew
the cap (anticlockwise).
2.Thefirsttimeyoudothis:fillthewater
tank right up to its edge.
3. Position the funnel*
(see figure)
and
fill the salt dispenser up to the edge
(approximately 1kg).It isnormal fora
little water to leak out.
4.Removethefunnel*andwipeanysaltresiduesawayfrom
the opening; rinse the cap under running water and then screw
it on, the head facing downwards so as to let the water flow out
of the four slots (star-shaped arrangement) in the lower part of
the cap (cap with green float*).
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
Whennecessary,measureoutthesaltbeforeawashcycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Only available in selected models.
Water Hardness Table
Average salt dispenser
capacity duration**
level °dH °fH mmol/l months
1 0 - 6 0 - 10 0 - 1 7 months
2 6 - 11 11 - 20 1,1 - 2 5 months
3 12 - 17 21 - 30 2,1 - 3 3 months
4 17 - 34 31 - 60 3,1 - 6 2 months
5*
34 - 50 61 - 90 6,1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the use of salt.
* a setting of 5 may increase cycle duration.
** 1 wash cycle per day.
G
F