Braun MR 6550 CA Blender User Manual


 
8
English
Our products are engineered to meet the
highest standards of quality, functionality and
design. We hope you thoroughly enjoy your
new Braun appliance.
Caution
Please read the use instructions carefully
and completely before using the
appliance.
The blades are very sharp!
Alwa
ys unplug the appliance when it is left
unattended and before assembling, disas-
sembling, cleaning and storing.
This appliance is not intended for use by
children or persons with reduced physical
or mental capabilities, unless they are
given supervision by a person responsible
for their safety. In general, we recommend
that you keep the appliance out of reach of
children.
Do not hold the motor part nor the whisk
gear box under running water, nor
immerse them in water.
Braun electric appliances meet applicable
safety standards. Repairs or the replace-
ment of the mains cord must only be done
by authorised service personnel. Faulty,
unqualified repair work may cause
considerable hazards to the user.
Before plugging into a socket, check
whether your voltage corresponds to the
voltage printed on the bottom of the
appliance.
The appliance is constructed to process
normal household quantities.
Neither the beaker , nor the chopper
bowl (c) is microwave-proof.
Description
Motor part
On/off switch for variable speed
Turbo switch
Buttons for releasing the working parts
Variable speed regulator
Blender shaft
Measuring beaker with air-tight lid
Whisk gear box
Whisk
Chopper
Setting the speed
When activating switch , the processing
speed corresponds to the setting of variable
speed regulator . The higher the setting, the
faster the chopping results.
However, maximum processing speed can
only be achieved by pressing the turbo
switch . You may also use the turbo switch
for instant powerful pulses without having to
manipulate the speed regulator.
Depending on the application, we recom-
mend the following speed settings:
Handblender 1...turbo
Chopper 1...turbo
Whisk 1...15
How to operate your handblender
The handblender is perfectly suited for
preparing dips, sauces, soups, mayonnaise
and baby food as well as for mixing drinks
and milkshakes.
1. Insert the motor part into the blender
shaft until it locks.
2. Introduce the handblender in the vessel,
then press the on/off switch or the
turbo switch .
3. To release the blender shaft after use,
press buttons and pull it off.
You can operate the handblender in the
measuring beaker , and just as well in any
other vessel. When blending directly in the
saucepan while cooking, take the pan from
the stove first to protect your handblender
from overheating.
How to operate your whisk
Use the whisk only for whipping cream,
beating egg whites and mixing sponges and
ready-mix desserts.
1. Insert the whisk into the whisk gear
box , then insert the motor part into
the gear box until it locks.
2. Place the whisk in a vessel and only then,
press switch to operate it.
3. To release, press buttons and pull off
the gear box. Then pull the whisk out of the
gear box.
For best results:
Do not use the beaker , but a wider bowl.
Move the whisk clockwise, holding it
slightly inclined.
Whi
pped cream
Only whip up to 400 ml chilled cream
(min. 30 % fat content, 4 – 8 °C).
Start with a low speed setting (1) and while
whipping, increase the speed to setting 15.
Egg snow
Only whip up to 4 egg whites.
Start with a medium speed setting (7) and
while beating, increase the speed to setting
15.
How to operate
your chopper
attachment
(a) Chopper gear box
(b) Blade
(c) Chopper bowl
(d) Anti-slip base/lid
The chopper is perfectly suited for chopping
meat, cheese, onions, herbs, garlic, carrots,
walnuts, hazelnuts, almonds etc.
For chopping hard goods (e.g. hard cheese),
use the turbo switch .
N.B.:
Do not chop extremely hard food, such
as ice cubes, nutmeg, coffee beans,
and grains.
Before chopping ...
pre-cut meat, cheese, onions, garlic,
carrots (see table page 5)
remove stalks from herbs, un-shell nuts
remove bones, tendons and gristle from
meet.
1. Caution: Carefully remove the plastic
cover from the blade. The blade is very
sharp!
Always hold it by the upper plastic part.
Place the blade on the centre pin of the
chopper bowl (c). Press it down until it
locks.
Always place the chopper bowl on the
anti-slip base (d).
2. Place the food in the chopper bowl.
3. Put the gear box (a) on the chopper bowl.
4. Insert the motor part into gear box (a)
until it locks.
5. Press switch or to operate the
chopper. During processing, hold the
A
H
G
A
B
C
D
E
F
G
H
I
J
B
E
C
A
F
B
C
D
G
I
H A
B
D
G
a
b
c
d
C
A
B C
98575354_MR6550_MCA_P6-36 Seite 8 Donnerstag, 13. März 2008 1:32 13