Dacor RDW24S Dishwasher User Manual


  Open as PDF
of 3
 
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
RDW24I, RDW24S
Renaissance 24” Wide
Built-In Dishwasher
Document # PG10-007
Revised 03/12/12 Page 2/3
Electrical Specifications
Dedicated Circuit Required
Total
Connected Load
Grounded, 3-prong, electrical outlet
supplied by 120 Vac,
60 Hz, 15 Amp. (circuit breaker)
11 Amp. @ 120 Vac, 60 Hz.
■ The above specifications are for reference only. For exact
specifications see the product data label, located inside the right door
■ Do not modify the power cord or use an extension cord. The power
cord may be disconnected from the appliance and hard-wired to a
junction box connected to a circuit meeting the above specifications if
the power cord is not long enough.
Water Supply Specifications
■ Water Pressure: The water supply pressure must be between 4.2
and 140 psi (30-1000 kPa). The water supply line and the shut-off
valve must supply a flow volume of at least 3 gallons (12 liters) per
minute.
■ Water Supply Temperature: The dishwasher can be connected to a
cold or hot water supply (maximum 160°F, 70°C). Dacor recommends
using a hot water supply of 120°F (49°C) to 140°F (60°C). If a cold
water supply is used, the washing times will be longer, but the
performance will not be affected.
■ Water Supply Valve Requirement: 3/8” water supply valve for
connection to dishwasher’s water supply line is required in a location
where it is easily accessible after the dishwasher is installed. The
dishwasher water supply line is equipped with a 3/8” (1.0 cm) NPT
female compression fitting on the end.
Location Specifications
■ Install in a location with convenient access, close to the kitchen sink
for easy water supply and drain connection. All minimum product
dimensions must be met or exceeded. Dimensions shown on this
page provide the required clearances.
■ The cabinet must enclose the dishwasher on top, back and sides.
■ Plan the installation so that the appliance can be removed easily if
service is required. The electrical outlet/junction box, water supply
valve and drain connection must be installed to the right or left of the
cutout and accessible when dishwasher is installed.
■ If dishwasher is installed in a corner, there must be a minimum
clearance of 2” (5.1 cm) from the side wall so the door can open. See
diagram.
E
F
24”
(61.0 cm)
4” (10.2 cm)
2” (5.1 cm)
5 3/8”
(13.6 cm)
DISHWASHER CUTOUT - FRONT VIEW
Cutout tolerances: +1/16” (+1.6 mm), -0
2” (5.1 cm) min.
clearance
Model (E) Cutout Width (F) Cutout Height
RDW24I*
23 5/8” (60.0 cm) to
24” (61.0 cm)
33 7/8” (86.0 cm) to
36” (91.4 cm)
RDW24S** 24” (61.0 cm)
34 3/8” (87.3 cm) to
36 1/2” (92.7 cm)
*If installing model RDWH24I in a 24” wide cutout installation of a trim kit
(Dacor PN 106925) is required to fill the space between the edge of the
cutout and the dishwasher.
** If the height of the existing cutout is too low:
■ Check to see if the cabinet face can be trimmed at the top. In many
cases, when a non-standard size dishwasher has been installed
previously, there is enough room inside the cabinet once the cabinet
face is modified.
■ The dishwasher can be shortened 1/4” (6.0 mm) by not installing the
plastic feet provided with the unit. Extra care must be taken if the feet
are not installed. Dacor is not responsible for floor damage during
installation.
■ The dishwasher can be shortened 1/4” (6.0 mm) by removing the trim
pieces that surround the wash compartment opening. NOTE: Doing
so will create a gap of 1/4” (6.0 mm) on the right and left side of the
door.
■ Floor must be solid and level. All cutout surfaces must be at right
angles. Surrounding cabinet must have sufficient material for
attachment of the anti-tip brackets (see installation instructions).
■ The electrical wiring, water supply and drain lines must enter through
the area indicated by the shading on the illustration below. Preferably,
they should come through the right side of the cabinet.
■ The access hole(s) in the cabinet for the power cord and water line
shallbenobiggerthan1-1/2˝(3.8cm)indiameter.Theaccesshole
forthedrainhoseshallbenobiggerthan2˝(5.0cm)indiameter.The
access holes for all three must be round and smooth. If the partition
is metal, it needs to be covered with an edge protector. Call Dacor for
the part number of an approved edge protector.
 previous