Filter
Top Products
Installation Using Your Dishwasher
Cold Water Connection
Connect the cold water supply hose to a threaded
Ÿ
3/4(inch) connector and make sure that it is
fastened tightly in place.
If the water pipes are new or have not been used for
Ÿ
an extended period of time, let the water run to
make sure that the water is clear. This precaution is
needed to avoid the risk of the water inlet getting
blocked and damaging the appliance.
WARNING!
In order to avoid water staying in the inlet hose,
please close the hydrant after using. (Not applicable
to appliances without aqua-stop.)
Drain Hose Connection
Insert the drain hose into a drain pipe with a
Ÿ
minimum diameter of 4cm, or let it run into the sink,
making sure to avoid bending or crimping it. Use
the special plastic support that comes with the
appliance . The top of the hose must be at a height
between 40 and 100cm. The free end of the hose
must not be immersed in water to avoid the back
flow of it.
Positioning the Appliance
Position the appliance in the desired location. The
Ÿ
back should rest against the wall behind it, and the
sides, along the adjacent cabinets or walls. The
dishwasher is equipped with water supply and
drain hoses that can be positioned either to the
right or the left sides to facilitate proper installation.
Put the dishwasher on the slide rails supplied.
Ÿ
Affix the condensation strip under the cabinet
Ÿ
bench top. Ensure the condensation strip is flush
with the edge.
Water Outlet
Connect the water drain hose. The drain hose must
Ÿ
be correctly fitted to avoid water leaks. Ensure that
the water drain hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to
Ÿ
use a similar drain hose.
It must be no longer than 4 metres; otherwise the
Ÿ
cleaning effect of the dishwasher could be
reduced.
Syphon Connection
The waste connection must be at a height of
Ÿ
between 40 cm (minimum) and 100 cm (maximum)
from the bottom of the dish. The water drain hose
should be fixed by a hose clip. The free end of the
hose must not be immersed in water.
Page 19Page 10
Max 1000mm
Min 400mm
Inlet pipe
connector
Min 100mm
Drain pipe
connector
DISHWASHER
SINK
WARNING!
DO NOT BEND IN ANY WAY!
FRONT VIEW
POWER
OUTLET
CONTROL PANEL
Delay 1/
2
Prog. Start/Pause
On/ Off
6 57 4 3 2 1
4
3
2
1
Power indicator light: To show the power
supply.
Power switch: To turn on/off the power supply.
Start/Pause button: To start the selected
washing program or pause the washing
program when the machine is working.
Program Button: To select your desired
program from the seven washing programs.
7
6
5
Half load functions Button: To select Half load
functions. (Half load function means that the
lower spray arm does not run, so you should
load the upper basket only).
Delay Button: To Press the button to delay.
Display window: Display the program, program
remaining time, delay time, fault codes and etc.
TURNING ON THE APPLIANCE
Starting a wash cycle:
1. Draw out the lower and upper basket, load the
dishes and push them back. It is recommended to
load the lower basket first, then the upper one (see
the section entitled “Loading the Dishwasher”).
2. Pour in the detergent (see Page 13).
3. Insert the plug into the socket. The power supply is
220-240 VAC /50 HZ, the specification of the
socket is 10A 250VAC. Make sure that the water
supply is turned on to full pressure.
4. Close the door, press the ON/OFF button, and the
ON/OFF light will turn on.
5. Press the program button to select your desired
program, then press the Start/Pause button, the
dishwasher begins to start.
NOTE: When you press the Start/Pause button to
pause during washing, the LED Display Window will
stop blinking and the dishwasher will moo every
minute unless you press the Start/Pause button to
start.
CHANGE THE PROGRAM
Premise:
1. A cycle that is underway can only be modified if it
has only been running for a short time. Otherwise,
the detergent may have already been released, and
the appliance may have already drained the wash
water.
If this is the case, the detergent dispenser must be
refilled (see the section entitled "Adding
Detergent").
2. Press the Start/Pause button, then press the
program button more than 3 seconds , the machine
will be in standby mode, then you can change the
program to the desired cycle setting (see the
section entitled " Starting a wash cycle. . .").
NOTE: During delay mode, press the Start/Pause
button, then you can change the program and
delay time.
3. The LED display shows the state of the dishwasher:
a) LED shows '-:--' -- Stand by
b) LED shows 'H:MM' and not blinking--Being paused
c) LED shows 'H:MM' and blinking--Running