Filter
Top Products
Installation Using Your Dishwasher
Page 17Page 8
Max 1000mm
Min 400mm
Inlet pipe
connector
Min 100mm
Drain pipe
connector
DISHWASHER
SINK
WARNING!
DO NOT BEND IN ANY WAY!
FRONT VIEW
POWER
OUTLET
FORGET TO ADD A DISH?
A forgotten dish can be added at any time before the
detergent cup opens.
1. Open the door a little to stop the washing.
2. After the spray arms stop working, you can open
the door completely.
3. Load the forgotten dishes.
4. Close the door, the dishwasher will start running
again after 10 seconds.
WARNING! It is dangerous to open the door when
washing, because the hot water may scald you.
AT THE END OF THE WASH CYCLE
When the working cycle has finished, the buzzer of
the dishwasher will sound for 8 seconds, then stop.
Turn off the appliance using the ON/OFF button, shut
off the water supply and open the door of the
dishwasher. Wait for a few minutes before unloading
the dishwasher to avoid handling the dishes and
utensils while they are still hot and more susceptible
to breakage. They will also dry better.
Switch off the Dishwasher
When the digital display shows ‘-:--’ (remaining
program time), the program has ended.
1. Switch off the dishwasher by pressing the ON/OFF
button.
2. Turn off the water tap!
Open the door carefully
The dishes should be allowed to cool down around
15 minutes before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a
few minutes before removing the dishes. Dishes will
be cooler and the drying will be improved.
Unloading the Dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one.
This will avoid water dripping from the upper Basket
onto the dishes in the lower one.
Cold Water Connection
Connect the cold water supply hose to a threaded
Ÿ
3/4(inch) connector and make sure that it is
fastened tightly in place.
If the water pipes are new or have not been used for
Ÿ
an extended period of time, let the water run to
make sure that the water is clear. This precaution is
needed to avoid the risk of the water inlet getting
blocked and damaging the appliance.
WARNING!
In order to avoid water staying in the inlet hose,
please close the hydrant after using. (Not applicable
to appliances without aqua-stop.)
Drain Hose Connection
Insert the drain hose into a drain pipe with a
Ÿ
minimum diameter of 4cm, or let it run into the sink,
making sure to avoid bending or crimping it. Use
the special plastic support that comes with the
appliance . The top of the hose must be at a height
between 40 and 100cm. The free end of the hose
must not be immersed in water to avoid the back
flow of it.
Positioning the Appliance
Position the appliance in the desired location. The
back should rest against the wall behind it, and the
sides, along the adjacent cabinets or walls. The
dishwasher is equipped with water supply and drain
hoses that can be positioned either to the right or the
left sides to facilitate proper installation.
Levelling
Once the appliance is positioned for levelling, the
Ÿ
height of the dishwasher may be altered via
adjustment of the screwing level of the feet. In any
case, the appliance should not be inclined more
than 2 °.
Water Outlet
Connect the water drain hose. The drain hose must
Ÿ
be correctly fitted to avoid water leaks. Ensure that
the water drain hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to
Ÿ
use a similar drain hose.
It must be no longer than 4 metres; otherwise the
Ÿ
cleaning effect of the dishwasher could be
reduced.
Syphon Connection
The waste connection must be at a height of
Ÿ
between 40 cm (minimum) and 100 cm (maximum)
from the bottom of the dish. The water drain hose
should be fixed by a hose clip. The free end of the
hose must not be immersed in water.