Filter
Top Products
2
PROTECT YOUR HOME!
The heat generated by the boiler unit can mark carpets, soft furnishings, table tops, cabinets etc.
To prevent this we recommend placing the unit on a wooden board, tray or other barrier - making sure it will not slip off
one side or tilt during use.
Dust sheets or newspapers are not suitable heat protectors for delicate surfaces.
CAUTION !
Check the state of your plaster before starting work.
Steam can loosen weak, porous or poorly bonded plaster - which also loosens readily if cracked, holed or if the steam
plate is held in one position for too long after the paper is soaked.
Weak plaster can normally be detected by tapping a few areas of wall. A hollow sound indicates that you should
proceed only with extreme care - stopping immediately if you hear a cracking sound or plaster starts to break loose.
The steam stripper is safe for drywall/plaster board surfaces but whatever the material, it is always wise to check a
small area before starting work properly.
PREPARATION
T
o achieve fastest paper removal always gently score the areas to be stripped.
With heavily embossed, vinyl coated or painted papers this is essential. Either use a proprietory
perforator tool or alternatively score the paper with the edge of a wall scraper in a criss-cross pattern
with 150mm (6 inch) spacing.
As with all decorating work be sure to protect carpets and furniture with covers.
●
Keep equipment away from children and pets.
●
Ensure boiler is placed on a flat level surface, and
should the boiler become tilted in use - level again
immediately.
Failure to do so can result in severe overheating,
complete element failure and void of your guarantee.
●
Block boiler unit securely if using on stairs.
●
The boiler becomes hot in use. Move only by using
the carrying handle.
●
Steam is produced at 100
o
C. Be careful, wear
protective clothing and protect your hands with heat
resistant gloves or mitts.
●
Never point hose or steam plate at anyone.
●
Always keep steam plate tilted away from face and
body, beware of hot drips and regularly empty
collected condensation from plate - especially when
stripping ceilings and high areas.
●
Never remove elbow filler cap or detach hose whilst
unit is operating.
●
Never block the safety valve.
●
Never use outside when raining.
●
Switch off and wait for 2 minutes before removing
elbow filler cap to refill boiler
.
●
Do not overfill the reservoir.
●
Allow to cool completely before emptying boiler.
●
Do not stand on boiler or hose.
●
Do not drag or try to move boiler by pulling with
hose or mains lead.
●
Do not allow water or steam to enter light switches
or power points.
●
Do not leave unattended.
●
Use only standard tap water. Never add detergents
or chemicals.
●
Extreme care must be taken if the unit is used in
bathrooms. Always be aware of danger of
electrocution from stored water in baths and sinks.
●
Never change tools when the unit is operating.
●
Always store upright.
●
It is recommended that a RCD (residual current
device) rated at 30mA is fitted into the mains supply
socket for added protection against electric shock.
●
Use only genuine Earlex replacement parts.
OPERATION
STEAM IS HOT! The unit is designed for safe, fast removal of wallpaper but please be aware that steam is produced at
100
o
C - so be careful, wear protective clothing and protect your hands with heat resistant gloves or mitts.
FILLING:
Remove elbow filler cap and fill unit to MAX. level indicator with clean - preferably hot - water.
Ensure that the ‘O’ ring is seated correctly on the elbow filler cap and place elbow filler cap lugs
into filler hole with the tongue pointing to the TWO O’CLOCK position. Turn the elbow filler cap
clockwise to the SIX O’CLOCK position so that the tongue locks into place between the two
teeth.
The capacity of 5 litres (9 pints) provides approx. 90 mins. steaming time before the safety cut-
out operates.
For a shorter steaming time use less water.
Do not overfill the unit or hot water will be
forced up the steam hose.
Screw hose onto threaded outlet of steam plate, hand tight is sufficient. Do not over tighten
but do check for hand tight fit from time to time during use.
Connect mains lead from unit to power socket and switch on. lt can take up to 15 mins (approx.) before steam is
produced - depending on fill water quantity and temperature.
Do not leave unattended and keep children & pets out of the room.
Just before full steam production a small amount of bubbling and water will occur at the steam plate.
Beware of hot water discharge prior to steam emission.