Electrolux 9CHG584107 Range User Manual


 
OPERATING INSTRUCTIONS
Page 10 62.9540.01_UL
D Wash the appliance panels using hot water to which a fat-
dissolving agent has been added, dry and polish if neces-
sary. No steel brushes, steel or copper wool or similar
utensils are to be used.
2.1 FINNED PAN RESTS
Use a sponge and lukewarm soapy water or another soft
detergent for cleaning. Do not use steel wool or abrasive
cleaning agents so as not to damage the enamel. If heavily
soiled, the pan rests should be soaked in soapy water over-
night.
Finned pan rests made of chrome nickel steel can be washed
in a washing machine.
2.2 HOTPLATE
From time to time use a steel brush to clean dirt and soot from
the plate and grease it lightly with commercial range plate
grease. Never use water for cleaning, as this would cause cor-
rosion.
2.3 BURNER
D Lift off the burner lid (1 / Fig. 11) and pilot burner body (3 /
Fig. 11).
D Soak overnight in soapy water.
D Clean thoroughly with a brush.
D Clean blocked holes (2 / Fig. 11) on the burner cover (1 /
Fig. 11) and holes in the pilot burner (7 / Fig. 11), blow
through if necessary.
D Do not use abrasive paper to clean the tip of the thermo-
element (7 / Fig. 11). The sensor must be free of cracks.
D Take great care that no dirt enters the gas supply line
(burner tube (4 / Fig. 11) and the pilot burner opening).
Cover these places if necessary.
D Thoroughly dry all the burner parts before reinstalling them.
Note:
The burner lid (1 / Fig. 11) must lie evenly and engage in
the burner body which must engage in the burner tube.
Ensure the correct positioning of the burner lid before light-
ing the burner. It must be fixed and only movable in the ver-
tical position.
CAUTION:
Wrong positioning of the burner lid can cause combustion
irregularities - danger of burning!
2.4 FLAME
In a visual check, the flames must be dark blue without any
upper yellow or orange tips; they must be stable and soot-free
and adhere firmly to the outlets.
If there is a lack of primary air, the flame has yellow streaks
and tips; if there is too much primary air, the flame is short,
transparent and tends to lift off the burner.
When the flame is correctly adjusted, it must not lift off or back-
fire when the burner is cold as well as warm.
The flame will backfire into the inside of the burner when the
speed of the gas-air mixture through the burner outlets is too
low, particularly when the air passages are dirty.
The different ignition processes must also take place without
any delays. This concerns: ignition, arc-through and extending
the flame over the whole burner area.
If the flame fails to meet all the requirements, cleaning or main-
tenance is necessary.
2.5 FAULTS
3. OPEN COMPARTMENT
The open compartment (Fig. 12) is integrated in the base unit.
Recommended accessories:
- Shelf fixation (1) 2 off
- Shelves (2) 1 off
1 Burner lid
2Drill holes
3 Burner body
4 Burner tube
5 Burner support
6 Pilot burner
7 Thermoelement tip
Fig. 11Burner
1
6
2
5
7
3
4
Fault Cause Remedy
Main burner
Sooty flame. Gas mix too rich.
Partially blocked burner
gaps.
- Clean burner
cap
.
Long yellow flame tips. Mixing tube narrowed
by dirt.
- Inform Customer
Service.
Flame lifts off from one or
more burners.
Exit velocity too high due
to blocked burner gaps.
Deformed burner
cap
.
Pressure regulator on
gas cylinder not
operating correctly.
- Cleaning the burner
cap
.
- Request replacement.
- Inform Customer
Service.
Flame flashes back. Mixture too lean.
Insufficient exit velocity
at burner gaps.
Soiled airways.
Blocked nozzle.
Deformed or burnt-out
burner cover.
- Inform Customer
Service.
- Request replacement.
Flame too small in one or
more burners.
Partially blocked nozzle.
Insufficient gas
pressure.
- Inform Customer
Service.
No flame at low setting. Blocked low setting
nozzle.
- Inform Customer
Service.
No flame in one or more
burners.
Completely blocked
nozzle or mixer tube.
Blocked gas tap.
•No gas.
- Inform Customer
Service.
- Check gas tap setting.
Pilot burner
No flame. Blocked burner gaps.
Blocked nozzle.
- Clean pilot burner cap.
Flame goes out after
control valve release.
Thermo-element insuffi-
ciently heated (dirty?).
•Defective
thermo-element.
- Remove dirt; do not use
abrasive paper!
- Inform Customer
Service.
Flame too small or too
large.
Primary air ratio
adjusted.
Nozzle blocked.
- Inform Customer
Service.
1 Shelf fixation
2 Shelves
Fig. 12Storage space