Filter
Top Products
Gas Slide-In Cooktop
E36GC75GSS
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
USA
•
250 Bobby Jones Expressway
•
Augusta, GA 30907
•
1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxicon.ca
E36GC75GSS 05/08 © 2008 Electrolux Home Products, Inc. Printed in the U.S.A.
36" Gas Slide-In Cooktop Specifications
•
Product Weight – 113 Lbs.
•
Voltage Rating –120V/1.2W/60 Hz/15 Amp
•
Connected Load (kW Rating) @120 Volts = 0.001kW (For use on
adequately wired 120V, dedicated circuit having 2-wire service with a
separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @120 Volts = 0.008 Amps
•
Always consult local and/or national electric and gas codes.
•
Cooktop ships with 3/4" factory regulator.
•
Lp conversion kit supplied.
•
Respect critical dimensions as noted for proper installation of cooktop.
•
Overhead cabinetry should not exceed a 13" maximum depth.
•
Allow 30" minimum clearance between top of cooktop and bottom of
unprotected wood or metal overhead cabinetry.
•
Absolute minimum horizontal distance between overhead cabinets
installed to either side of appliance must be no less than maximum width
of appliance.
•
Allow 24" minimum clearance when bottom of wood or metal overhead
cabinet is protected by not less than 1/8" flame-retardant millboard
covered with not less than No.28 MGS sheet steel, 0.015" stainless
steel, 0.024" aluminum or 0.020" copper.
•
Allow 1" minimum clearance between rear edge of cutout and nearest
combustible surface above countertop.
•
Allow 7" minimum clearance from edge of cooktop to nearest
combustible wall on either side of unit.
•
It is recommended that drawers not be used beneath cooktop.
•
To reduce risk of fire when using overhead cabinetry, install vent hood
that projects horizontally a recommended minimum of 7" beyond bottom
of cabinets.
•
Gas Slide-In Cooktop model E36GC75GSS is NOT approved to be
used over any Electrolux ICON
™
Single Wall Oven.
•
Gas Slide-In Cooktop model E36GC75GSS (without optional backsplash)
is approved to be used in combination with an Electrolux ICON
™
Downdraft Vent. (Refer to Slide-In Cooktop/Downdraft Vent Countertop
Preparation Specifications page and on web.) Proper combination
installation will require cooktop power cord to be relocated to underside
of unit. (For details, refer to 30" & 36" Gas Slide-In Cooktop Power Cord
Relocation Instructions on web.)
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
Optional Accessories
•
When replacing an existing cooktop with countertop cutout deeper
than 7-1/4" and less than 8-1/2", order free Depth Adjustment Filler Kit –
(903051-9010).
•
9" Stainless Steel Backsplash – (903048-9010).
•
Black Knobs Kit – (903049-9120).
35
3
/16"
7
1
/2"
18"
min.
*35
3
/16"
*Both cutout dimensions are critical to proper cooktop
installation. Due to variations in countertop materials
it is recommended to undercut finished dimension
(35-15/16") and adjust upon installation of cooktop.
*35
15
/16"
24"
7
1
/4"
3
/8"
30" min. for
unprotected cabinet
24" min. for
protected surface
22"
1
1
/8"
max.
25" min.
36" min.
13"
max.
cabinet
depth
1" min. recommended
distance between rear
edge of cutout and
nearest combustible
surface above countertop
3"
2" dia.
opening to route
power cable
2
1
/2"
2"
4" x 4" opening to
route gas supply
7" min. to nearest
combustible wall
(either side of unit)
Side inset
3
/8"
Optional 9" stainless
steel backsplash
7
3
/4"
25
3
/4"
35
7
/8"
2"