Electrolux EI36WC40GS Ventilation Hood User Manual


 
1111
1111
11
Outside rOutside r
Outside rOutside r
Outside r
ear exhaustear exhaust
ear exhaustear exhaust
ear exhaust
(Horizontal duct– 3 1/4”x 10” Rectangular)
Use the diagram or the hood as a template
and mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Center line
Hood mounting screws (4)
Wood shims (recessed
bottom cabinets only)
Cabinet front
Electrical access hole
(in wall)
Cabinet
bottom
1/8"
7/16"
13 15/16" (30" Hood)
16 15/16" (36" Hood)
13 15/16" (30" Hood)
16 15/16" (36" Hood)
Horizontal duct
access hole
5 1/4" 5 1/4"
12 7/16"
3 3/4"
RecirRecir
RecirRecir
Recir
culatingculating
culatingculating
culating
Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
Step 9Step 9
Step 9Step 9
Step 9
Choose VChoose V
Choose VChoose V
Choose V
enting Optionenting Option
enting Optionenting Option
enting Option
The hood can be set to vent outside or to recirculate
air back into the kitchen.
Set for
outside venting
Set for
recirculating
Stop tab
Stop tab
Hood shown Lying upside down
The plastic vent lever is located near the center of the
hood opening.
TT
TT
T
o vent to the outside, o vent to the outside,
o vent to the outside, o vent to the outside,
o vent to the outside, make sure the plastic vent
lever is in the
HORIZONTHORIZONT
HORIZONTHORIZONT
HORIZONT
AL AL
AL AL
AL position (flat against the
metal top of the hood).
TT
TT
T
o ro r
o ro r
o r
ecirecir
ecirecir
ecir
culate air into the kitchen, culate air into the kitchen,
culate air into the kitchen, culate air into the kitchen,
culate air into the kitchen, make sure the
plastic vent lever is in the
VERVER
VERVER
VER
TICAL TICAL
TICAL TICAL
TICAL position (flat
against the plastic blower housing).
NOTE: NOTE:
NOTE: NOTE:
NOTE: In order to change the vent lever position, you
will need to pull the lever out slightly to clear the
plastic tabs.
Step 10Step 10
Step 10Step 10
Step 10
For rFor r
For rFor r
For r
ecessed bottom cabinet onlyecessed bottom cabinet only
ecessed bottom cabinet onlyecessed bottom cabinet only
ecessed bottom cabinet only
If the cabinets have front, side or back trim, make 2
wood shims the width of the trim and attach them to
the cabinet bottom recess on both sides. See
previous page for marking locations.
Step 11Step 11
Step 11Step 11
Step 11
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3/4” extra toward
the front of the cabinet so you can move the duct
freely when installing the hood.
It may also ease installation by cutting the hole 10 1/
2” instead of 10”.
Step 12Step 12
Step 12Step 12
Step 12
Drive a mounting screw (from the hardware packet)
partway into each center of the narrow neck of the
keyhole slots marked on the cabinet bottom.
Step 13Step 13
Step 13Step 13
Step 13
Fix the wiring conduit to the hood.
Step 14Step 14
Step 14Step 14
Step 14
Slide the hood back against the wall. Tighten the
mounting screws. Be sure the screw heads are in the
narrow neck of the keyhole slot.
Connect Ductwork to hood.
WW
WW
W
ood shimsood shims
ood shimsood shims
ood shims
Installing the hood