Filter
Top Products
8
CONNECTING THE WATER SUPPLY
Before Installing The Water Supply Line,
You Will Need:
• BasicTools:adjustablewrench,at-blade
screwdriver, and Phillips
TM
screwdriver
• Access to a household cold water line with
water pressure between 30 and 100 psi.
• A water supply line made of ¼ inch (6.4
mm) OD, copper or stainless steel tubing.
To determine the length of tubing needed,
measure the distance from the ice maker inlet
valve at the back of the refrigerator to your
cold water pipe. Then add approximately 7
feet (2.1 meters), so the refrigerator can be
moved out for cleaning (as shown).
• A shutoff valve to connect the water supply
line to your household water system. DO NOT
use a self-piercing type shutoff valve.
• A compression nut and ferrule (sleeve) for
connecting a copper water supply line to the
ice maker inlet valve.
WARNING
To avoid electric shock, which can cause
death or severe personal injury, disconnect
the refrigerator from electrical power before
connecting a water supply line to the
refrigerator.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing
is recommended for the water supply line.
Water supply tubing made of ¼ inch plastic
is not recommended to be used. Plastic
tubing greatly increases the potential for
water leaks, and the manufacturer will not be
responsible for any damage if plastic tubing
is used for the supply line.
• DO NOT install water supply tubing in areas
where temperatures fall below freezing.
• Chemicals from a malfunctioning softener
can damage the ice maker. If the ice maker
is connected to soft water, ensure that the
softener is maintained and working properly.
IMPORTANT
Ensure that your water supply line connections
comply with all local plumbing codes.
NOTE
Check with your local building authority
for recommendations on water lines and
associated materials prior to installing your
new refrigerator. Depending on your local/
state building codes, Frigidaire recommends for
homes with existing valves its Smart Choice
®
water line kit 5305513409 (with a 6 ft. Stainless
Steel Water Line) and for homes without an
existing valve, Frigidaire recommends its Smart
Choice
®
water line kit 5305510264 (with a 20
ft. Copper Water Line with self-tapping saddle
valve). Please refer to www.frigidaire.com/store
for more information.
To Connect Water Supply Line To Ice Maker
Inlet Valve
1. Disconnect refrigerator from electric power
source.
2. Place end of water supply line into sink or
bucket.TurnONwatersupplyandush
supply line until water is clear. Turn OFF water
supply at shutoff valve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve) onto
water supply line. Push water supply line into
water valve inlet as far as it will go (¼ inch
/ 6.4 mm). Slide ferrule (sleeve) into valve
inletandngertightencompressionnut
onto valve. Tighten another half turn with a
wrench; DO NOT over tighten. See Figure 1.
If you use stainless steel tubing - The nut and
ferrule are already assembled on the tubing.
Slide compression nut onto valve inlet and
ngertightencompressionnutontovalve.
Tighten another half turn with a wrench; DO
NOT over tighten. See Figure 2.
5. With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel
of refrigerator as shown.
6. Coil excess water supply line (copper tubing
only), about 2½ turns, behind refrigerator
as shown and arrange coils so they do not
vibrate or wear against any other surface.
7. Turn ON water supply at shutoff valve and
tighten any connections that leak.
8. Reconnect refrigerator to electrical power
source.