Haier HDW100WHT Dishwasher User Manual


 
Cleaning and Special Maintenance
Filter Assembly
For the best performance and results, the filter assembly must
be keep clean.
The filter removes food particles from the wash water, allowing
the water to be recirculated during the cycle. For this reason, it is
a good idea to remove any food particles trapped in the filter
after each wash cycle by rinsing the semi-circular filter and cup
("A") under running water. To remove the filter assembly, pull
the handle in an upward direction. The entire filter assembly
(made up of the semicircular filter "A" and the fine filter "B")
should be cleaned at least once a month use a soft brush. To
reassemble, insert the entire assembly into the dishwasher, lo-
cate it correctly in its seat and pressing downward.
The dishwasher must not be used without the filters. Improper
replacement of the filters may reduce the performance of the
appliance.
Cleaning the Spray Arms
Food particles may become encrusted on the spray arms and
block the hole (see "Close up view [interior]" on page 3, letters
C-E ). Check the spray arms periodically and clean them when
needed.
Troubleshooting
A
B
.8.
Resolving minor problems yourself
Experience has shown that you can resolve most problems that
rise during normal daily usage yourself, without having to call
out a service engineer.Not only does this save costs,but it also
means that the appliance is available for use again that much
sooner. The following list of common occurrences and their rem-
edies should help you identify the causes of most problems.
Problems...
...when the appliance is switched on
Appliance does not start up
Fault with fuse in mains electricity supply.
Plug not inserted in wall socket.
Appliance door not closed properly.
Knob stay at the mark of "RESET"
Water tap not turned on.
Blocked strainer in water intake hose.
- The strainer is situated in the Aquastop or supply-hose connection.
Caution
Do not forget that repairs should only be carried
out by a qualified specialist. Improper repairs can
lead to considerable equipment damage as well
as danger to the user.
...with the appliance itself
the water is turned on and the hose is connected properly;
the water supply to the house is on and has sufficient pressure;
the water supply hose is crimped or bent;
the filter for the water supply hose is clogged.
the drain hose is too low.
the drain hose is crimped or bent.
the drain hose is too high.
the drain hose is too low.
If you take all these checks and the dishwasher still does
not function or your dishwasher have any other error
display, you can power the dishwasher OFF, and wait a
few minutes. You can power the dishwasher on, try it
again, if the dishwasher still does not function and/or the
problem persists, contact the nearest authorised service
center and provide them with the following information:
the nature of the problem.
the model type number (Mod...) And the serial number (S/
N...), which are indicated on the plate located on the side of
the inner part of the door.
Lower spray arm rotates with difficulty
Spray arm is blocked by small items or food remains.
When the alarm sounds in a series of 2 beeps, pause,
2 beeps, pause ...
When the alarm sounds in a series of 3 beeps, pause,
3 beeps, pause ...
When the alarm sounds in a series of 6 beeps, pause,
6 beeps, pause ...
When the alarm sounds in a series of 4 beeps, pause,
4 beeps, pause ...
Temperature sensor failed and call your Authorised Service Center.
When the alarm sounds in a series of 5 beeps, pause,
5 beeps, pause ...
Flood switch has been activated and call you Authorised Ser-
vice centre.
When the "END" indicator is on, at the moment, the
alarm sounds in a series of 7 beeps, pause, 7 beeps,
pause ...
the door is not properly closed.