Hobart CLCS86ER Dishwasher User Manual


 
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
As continued product improvement is a policy of Hobart, specications are subject to change without notice.
CLCS86eR
DISHWASHER
Page 12 of 12 F-40297 – CLCS86eR Dishwasher
F-40297 (06/11) LITHO IN U.S.A. (H-01)
SPECIFICATIONS: Meets requirements of A.S.S.E. Standard No.
1004.
DESIGN: Semi automatic, high temperature double-tank, rack-
type dishwasher with exible thermal layer curtains at the ends of
chamber and between prewash, wash, rinse and nal rinse zones.
Insulated hinged inspection doors located in front of machine
provide easy access to wash arms, rinse arms, strainer, strainer
basket, and pump intake screen. Length of machine inside tank (at
table connection) 86". Machine designed to clean and sanitize with
hot water 160°F wash, 160° power rinse and 180°F (minimum) nal
rinse. Water hardness recommended to be 3 gr. for best results.
Automatic interlocks shut off pump and conveyor if door is opened
when machine is in operation.
CONSTRUCTION: Tanks, chambers, frame, legs, control box,
doors, and all panels are constructed of stainless steel.
PUMPS: Three recirculating stainless steel pumps and impellers
with ceramic seat seals. Easily accessible pump assembly permits
quick inspection. The pumps are self-draining. All piping distrib-
uting water to the upper and lower wash arms is stainless steel
tubing.
PUMP MOTOR: Built for Hobart 2 hp grease-packed ball bearings,
splash proof, ventilated with manual, resettable inherent overload
protection. Available in electrical specications of 208-240/60/3,
480/60/3 and 600/60/3. Also available, but not submitted for UL
listing are 200-240/50/3 and 380-415/50/3.
ENERGY RECOVERY COIL: The condensing system using a tube
and n coil constructed of copper and corrosion resistant alumi-
num.
CONTROLS: A stainless steel control module with power and
“start/stop” buttons is mounted on top of the machine. Machine
control circuitry will be operated from a 120-volt control circuit
transformer. Electrical components are completely wired with
105°C, 600V thermoplastic insulated wire with stranded conductors
routed through UL listed electrical conduit or covered wire way.
CONVEYOR: Rapid Return drive, designed for more even through-
put of racks and allows for an 18.75-inch sepa ration between the
wash and the rinse zone. Racks conveyed automatically through
wash and rinse zones. Ball Detent Clutch drive prevents damage
to machine or racks, should movement of racks be obstructed.
Conveyor speed: 9.5 FPM.
DRIVE MOTOR: Built for Hobart,
1
6 horsepower gear motor,
ventilated with manual, resettable inherent overload protection.
Available in electrical specications of 208-240/60/3, 480/60/3 and
600/60/3. Also available, but not submitted for UL Listing are
200-240/50/3 and 380-415/50/3.
CORNER POWER SCRAPPER: CLCS86eR power scrapper is
equipped with an upper and lower wash arm with specially
shaped nozzles having large openings and arranged to effectively
scrap all types of tableware. Power scrapper arms and end caps
are easily removable for cleaning without use of tools. Removable
perforated stainless steel strainer pans support a deep perforated
stainless steel basket. Basket and strainer pans (3) can be
removed without lower wash arm removal.
POWER WASH AND RINSE: Wash and rinse tanks are equipped
with upper and lower stainless steel CFD Wash Arms which
effectively direct water jets to all ware surfaces. Both upper and
lower wash arms are self-aligning and have easily removable end
caps for cleaning without use of tools. A removable perforated
stainless steel strainer pan supports a deep perforated stainless
steel basket.
FINAL RINSE: Final rinse ow rate: 2.2 gpm, .39 gpr, 132-gph.
Stainless steel upper and lower Auto Position Rinse Arms
have
single rows of nozzles. Racks entering the rinse zone automatically
trigger rinse. Final rinse water line is equipped with a vacuum
breaker downstream of an electrically operated solenoid valve
in common piping system. Rinse agent dispenser injection ports
provided in nal rinse piping above chamber.
FILL: Fill water line is equipped with vacuum breaker on down-
stream side of electrically operated solenoid valve in common
piping system, for automatic maintenance of tank level.
DRAIN AND OVERFLOW: Large bell-type automatic overow
and drain valve controlled from inside of machine. Power scrap-
per overows to drain. Wash tank drain controlled from inside of
the machine overows to power scrapper through large internally
mounted stainless steel tubing. Drain seals are large diameter
high temperature o-rings. Drain automatically seats by closing
inspection doors. Common drain utilizes a removable large
diameter stainless steel tube sealed by rubber o-rings at each drain
housing. Drain housing can be plumbed from load or unload end of
machine.
STANDARD EQUIPMENT: Energy Recovery, Digital display of
power scrapper, wash and nal rinse temperature. Positive low
water protection for tank heat. Thermal Layered Curtains through-
out machine are keyed to ensure proper placement. Drains are
automatically closed when inspection doors are closed. Stain-
less steel adjustable feet. Bolted stainless steel enclosure panels
around perimeter and underneath machine. Automatic tank ll.
Door interlock. Auto-timer. Vent fan and booster heater controls.
Single point electrical connection. Low temperature alerts. Service
diagnostics. Dirty water indicator. Delime notication. Conveyor
dwell. Energy Saver Mode. NAFEM Data Protocol compliant.
Pressure regulating valve. Booster heater (30 kw).
WASH TANK HEATING SELECTIONS (must choose one):
ELECTRIC: Two electric Incoloy
®
sheathed immersion heaters
(15 KW and 10 KW) removable from inside tank. Tank water tem-
perature is controlled by microprocessor controlled thermostat with
positive low-water protection and magnetic contactor. (Disconnect
switches not furnished.) A high limit device mounted on the surface
of the tank additionally protects heating element.
STEAM: One-inch stainless steel steam coil. Tank water
temperature controlled by microprocessor controlled thermostat
with positive low-water protection. Steam supplied to machine
through high temperature steam solenoid valve and line strainer.
GAS: Regulated infrared immersion tube gas burner system.
Microprocessor controlled thermostat and a blower with a pressure
switch control tank water temperature. Positive low water protec-
tion is provided. A high limit device mounted on the surface of the
tube additionally protects immersion tube. A solid-state igniter
board controls the gas valve and provides ame ignition. A trans-
former steps the control circuit voltage down from 120 volts to 24
volts to power the igniter board and gas valve. For natural gas, gas
pressure to burner (customer connection) not to exceed 7" W.C.
For LP gas, gas pressure to burner (customer connection) not to
exceed 11" W.C. If gas pressure is higher than 7" W.C. natural or
11" W.C. LP pressure regulating valve must be supplied (by others)
in the gas line to the dishwasher.
OPTIONAL EQUIPMENT AT EXTRA COST:
Stainless steel vent hoods with vent stack, and locking-type
damper (load end only). Canopy exhaust power vent kit. Higher
than standard chamber. Side loaders and unloaders. 19
3
4" x 19
3
4"
peg, combination and miscel laneous racks. Table limit switch.
Drain water-tempering kit.