Filter
Top Products
5
D
ISHWASHER
Installation
Choose where you want to install
your dishwasher, you can place it
so that its sides or back panel are
side by side with furniture or up
against the wall. The dishwasher
is provided with water supply and
drain hoses, which can be
directed towards the left or right to
facilitate appropriate installation.
Levelling.
Once the appliance is positioned,
adjust the feet by screwing them
in or out depending on how high
you want it and to level it so that it
is horizontal. Make sure that it is
not inclined more than 2 degrees.
If the appliance is level, it will
help ensure its correct operation.
Height Adjustment
Insert the appliance into the cutout
and then adjust the height using
the screws located on the front
bottom part of the machine. Use a
screwdriver to turn the screws in
the clockwise or anti-clockwise
direction to increase or decrease
the height respectively.
Drain hose connection.
WARNING: Connect your
dishwasher drain hose to pipes
which connect to the foul drain
system and not to surface water
drains.
IMPORTANT: For the correct
operation of your dishwasher, it is
essential to comply with the
following information:
Standpipe:
Ensure that the hose is not pushed
too far down the standpipe.
If the end of your drain hose is fitted
with ‘retaining flaps’, ensure they are
inserted fully into the standpipe. This
will prevent the pipe from jumping
out during installation and use.
DO NOT position the standpipe near
an electrical outlet.
ENSURE that the drain hose is not
kinked and it is routed as shown in
the diagram.
The standpipe should have a bore
of at least 38mm (11/2”). It should
be installed as shown, have a trap
fitted and must discharge into the
same drain system as your
household sink.
It MUST NOT be connected to a
surface water drain.
Anti-flooding protection
Your dishwasher has a special
system which stops the water
supply in the event of leaks inside
the appliance.
It is equipped with a water inlet
that has a clear outer hose and an
inner high pressure hose which
turns bright red if it breaks.
Leaks are prevented as the clear
outer hose now contains the
water.
It is vital that you check it on a
regular basis, if you see it has
turned bright red, you know you
need to replace it as soon as
possible.
Call for an authorised technical
engineer to come and replace it.
Sink Waste System:
For under sink drainage:
Before connecting the drain hose,
remove any internal restrictions -
This will prevent a build up of debris
which could cause a blockage.
Remove any restrictions from the
waste spigot and ensure that the
sealing bung is removed. The hose
should be routed, such that it is
raised to a minimum height of
800mm (31/2”).
NOTE: Ensure the sink outlet
pipe has a minimum diamtere of
32mm.
1. Untie the end of the GREY
drainage hose from the rear of
the appliance.
2. Reposition the ‘Hooked End
Support’ as required along the
GREY drainage hose.
3. If fitting an under sink waste
disposal unit, cut out the
membrane, bung or blanking
plug.
Ensure the drain hose is
securely attached, to prevent
it coming away while the
machine is in use and causing
a flood.
Cold water connection.
Connect the cold water supply
hose to a 3/4 gas threaded
connection, taking care to screw it
tightly onto the tap. If the water
hoses are new or have been out
of use for an extended period of
time, let the water run to make
sure it is clear and free of
impurities before making the
connection. If this precaution is
not taken, the water inlet could get
blocked, causing damage to your
dishwasher.
Condensation-proof tape.
On some models, a transparent
condensation-proof adhesive tape
has been provided.
It should be stuck onto the lower
side of your wooden worktop to
protect it from the formation of
condensation.
When not provided, this tape can
be requested as a spare part from
authorised retailers.