Filter
Top Products
7
D
ISHWASHER
First of all.
- Turn on the water supply tap
completely.
- Add the correct amount of
detergent.
- Load the baskets correctly.
- Check that the spray arms rotate
freely.
- Close the door securely.
- Press the ON-OFF button "A":
indicator light "B" comes on. Your
appliance is now on and awaiting
instructions.
Select the wash cycle.
Select the wash cycle by
pressing button "P". Each time
this button is pressed, one of the
indicator lights “M” will come on
in sequence.Select the wash
cycle most suitable for the type of
dishes to wash (see ‘Programme
Chart’).
Close the door and after a few
seconds, you will hear a short
beep: the wash cycle has started.
Modifying a wash cycle in
progress.
If you have chosen the wrong
cycle - You can modify the wash
cycle in progress, if it has only
just started. Open the door
carefully, to avoid any hot water
splashes. Then keep button "P"
pressed for approximately 5
seconds, a prolonged beep will
sound followed by three short
beeps.
Indicator light "M" will go out to
show all the settings will have
been cancelled. You are now free
to re-set the correct wash cycle.
You've left out a dish?
Interrupt the wash cycle by
opening the door, carefully, then
insert the dish you had forgotten.
When you shut the door the cycle
will start up from where you
interrupted it.
Cycle end
The end of the wash cycle is
indicated by 2 short beeps and
the flashing of the wash cycle
indicator light “M”.
Open the dishwasher door.
Warning:
Turn the appliance off by pressing
button “A”, unplug the appliance
from the electricity socket to cut
off the power supply; the power
supply cable should consequently
be easily accessible.
- Turn off the water tap.
- Wait a few minutes before
unloading the dishes: they are
very hot! If you wait a little while,
they dry better due to the steam.
- Empty the lower basket first.
There's been a power
failure or you opened the
dishwasher door
The wash cycle stops and then
restarts when the electricity
comes back on or when you close
the door.
How to use your Dishwasher
Delaying the start of a
programme.
When you have loaded the
dishes, you can choose when to
start your dishwasher before
setting the wash cycle desired.
Press button "C" to delay the
start of the wash cycle by 2, 4 or 6
hours. Each time you press it,
you will hear a short beep and
indicator light "D" corresponding
to the selected delay will come
on.
Select the desired wash cycle.
Close the door and, after you hear
the beep, the countdown to the
delayed start will begin.
If, for example, you have set the
delayed start to 6 hours, the 6
hour indicator light will flash, then
the 4 hour indicator light will flash,
and finally the 2 hour indicator
light. The indicator lights will keep
you informed of the countdown
progress at all times.
Once this time is up, indicator
light "D" will stop flashing and
the wash cycle will begin.
If you change your mind and you
wish to set a different delay, just
open the door, press button "C"
and repeat the selection.
If you want to cancel the delay set
and you wish to start the wash
cycle immediately, press the
button in sequence until indicator
light "D" comes off.
Once you close the door, the
wash cycle set previously will
begin.
Half load.
Your dishwasher also allows you
to wash half a load, to save water
, electricity and detergent (use
only half the amount).
Before setting a wash cycle ,
press button "Q" repeatedly to
select whether you want to run a
half cycle on the upper or lower
basket. Each time you press it,
you will hear a short beep and
indicator light "R" corresponding
to the selected basket will come
on.
Extra drying
Press button "E" before you start
the selected wash cycle.
A prolonged beep will inform you
that you have selected extra
drying, a short beep indicates it
has been cancelled.
With extra drying, the wash cycle
will last longer, to provide you
with drier dishes.