Filter
Top Products
16
GB
CLEANING THE DOORS
Take particular care not to damage the innerTake particular care not to damage the inner
Take particular care not to damage the innerTake particular care not to damage the inner
Take particular care not to damage the inner
surface of the door inner glass that is coatedsurface of the door inner glass that is coated
surface of the door inner glass that is coatedsurface of the door inner glass that is coated
surface of the door inner glass that is coated
with a heat reflective layer. Do not usewith a heat reflective layer. Do not use
with a heat reflective layer. Do not usewith a heat reflective layer. Do not use
with a heat reflective layer. Do not use
scouring pads, or abrasive powder,which willscouring pads, or abrasive powder,which will
scouring pads, or abrasive powder,which willscouring pads, or abrasive powder,which will
scouring pads, or abrasive powder,which will
scratch the glass. Ensure that the glassscratch the glass. Ensure that the glass
scratch the glass. Ensure that the glassscratch the glass. Ensure that the glass
scratch the glass. Ensure that the glass
panel is not subjected to any sharppanel is not subjected to any sharp
panel is not subjected to any sharppanel is not subjected to any sharp
panel is not subjected to any sharp
mechanical blows.mechanical blows.
mechanical blows.mechanical blows.
mechanical blows.
Stubborn stains can be removed by using a fine
steel wool soap pad. For slight soiling theinner glass
panel may be cleaned, while still warm, without
removing it from the door. Aftercleaning, rinse and
dry with a soft cloth.
SIDE OPENING DOORS
Cleaning the door glass is the same as theCleaning the door glass is the same as the
Cleaning the door glass is the same as theCleaning the door glass is the same as the
Cleaning the door glass is the same as the
drop down doors, except take care todrop down doors, except take care to
drop down doors, except take care todrop down doors, except take care to
drop down doors, except take care to
support the weight of the inner glass whensupport the weight of the inner glass when
support the weight of the inner glass whensupport the weight of the inner glass when
support the weight of the inner glass when
removing and refitting.removing and refitting.
removing and refitting.removing and refitting.
removing and refitting.
DROP DOWN DOORS
Remove the door inner glass as follows.Remove the door inner glass as follows.
Remove the door inner glass as follows.Remove the door inner glass as follows.
Remove the door inner glass as follows.
1. Open the door fully and remove the extrusion end
caps (This should be done by hand but if it
proves too difficult, simply lift the inner glass to
ease the end caps out of position).
NOTE: If you need to use a tool - beNOTE: If you need to use a tool - be
NOTE: If you need to use a tool - beNOTE: If you need to use a tool - be
NOTE: If you need to use a tool - be
careful not to damage the extrusion or endcareful not to damage the extrusion or end
careful not to damage the extrusion or endcareful not to damage the extrusion or end
careful not to damage the extrusion or end
cap.cap.
cap.cap.
cap.
2. Carefully slide the inner glass towards you
andwithdraw it from its locating slots. Ensure that
the door is not allowed to slam shut, due to the
reduction in door weight. Clean the glass as
described above.
3. The inside of the outer door glass can now be
cleaned while still fitted to the cooker.
NEVER OPERATE THE COOKER WITHOUT THE
INNER DOOR GLASS IN POSITION.
Refit the door inner glass as follows.Refit the door inner glass as follows.
Refit the door inner glass as follows.Refit the door inner glass as follows.
Refit the door inner glass as follows.
1. Open the door fully.
2. Locate the inner door glass into its slots, so that
the printing is readable from the face nearest the
oven in the closed position and the widest black
band is towards the bottom of the door. The inner
door glass has a special reflective coating on one
side, in order to minimise surface temperatures
and energy consumption during use, it is
important it is fitted correctly.
3. Carefully slide the glass into its slots as far as it
will go and replace the end caps.
'Stay Clean' Panel
'Stay Clean' panels are covered with a special enamel
which absorbs cooking soils. At higher temperatures
the soiling is slowly destroyed. In most cases normal
cooking at higher temperatures will permit this cleaning
to take place automatically. However, if higher cooking
temperatures are not used regularly then it may be
necessary, in order to prevent heavy soiling, to run the
oven at maximum temperature for at least two hours,
from time to time. The 'Stay Clean' panel can be
washed in warm soapy water followed by rinsing in
clear water. Dry well with a soft cloth.
NOTE: Do not use enzyme washing powder, harsh
abrasives or chemical oven cleaners of any kind.