Filter
Top Products
108 [2743mm]
34 [864mm]
8
1
2
[218mm]
21 [533mm]
25 [635mm]
12 [307mm]
25 [635mm]
C
B
Drive
Unit
1
2
[15mm]
84 [2134mm]
A
O
N
Dish Clearance
With Doors Open
Rear of
Machine
Table to Table
Overall
6 [152mm]
Left Side
Right Side
Floor Sink Or Drain
With 3" (76 mm)
Minimum Drain Line
4" (102 mm) wide x 16" (406 mm)
long cutout in Vent Cowl/Splash
Shield. Shipped with Cover Plate.
Minimum
Scrap
Trough
14 [355mm]
25 [635mm]
21 [533mm]
8 [203mm]
64 [1626mm]
36 [914mm]
Base Unit
Prewash
Left to Right
Prewash Plan View Section
with Cold Water Thermostat
16
3
4
[425mm]
16
1
4
[415mm]
N
O
3/4" [19 mm]
Table Turndown
Flange 3/4" Max
21" [533 mm]
Rack Rail Height
Above Dishtable
1/4" [6mm] - 5/16" [8mm]
Rack Rail
Tub
Table
Use Silicone Sealer
Between Table and
Lip of Machine to
Prevent Leakage
Recommended Table Fabrication
Note: Tub Will Accept
a Table Flange
Up to 24 7/8"
[632 mm]
66
1
2
[1692mm]
65
1
2
[1666mm]
1 [25mm]
65
1
2
[1665mm]
100 [2540mm]
116 [2946mm]
32
3
4
[833mm]
10
1
2
[264mm]
Drive
Unit
75
1
2
[1918mm]
60
1
4
[1529mm]
62
1
2
[1590mm]
29 [737mm]
10 [254mm]
O
4 [102mm]
G
24 [609mm]
59
3
4
[1519mm]
N
A
23
1
2
[598mm]
6 [152mm]
7 [178mm]
D
E
B
33
1
2
[851mm]
8 [206mm]
14 [356mm]
Minimum
10" High
Table
Backsplash
Scrap
Trough
Front View
C
10 [255mm]
12
1
2
[316mm]
F
17
1
2
[442mm]
6
1
2
[162mm]
11
1
2
[295mm]
15
3
4
[400mm]
16
1
2
[417mm]
43 [1092mm]
L
H
J
M
11
1
4
[285mm]
13
1
2
[345mm]
23
3
4
[604mm]
38 [966mm]
6
1
4
[159mm]
5
3
4
[148mm]
4
1
4
[110mm]
8
1
2
[218mm]
H
J
L
M
K
F
Legend
A - Machine water inlet 3/4" NPT 180°F
Hi-temp,140°F Low-temp minimum
B - Electrical connection
C - Drain connection 1-1/2" NPT
D - Vent collar - Optional
E - Vent cowl standard
F - 3/4" NPT Steam connection
G - 3/4" NPT Condensate return
H - Steam electrical connection
J - 1" NPT Steam connection
K - 3/4" Condensate connection
L - 3/4" NPT Incoming 110°F water
connection
M - 3/4" NPT 180°F water to dishmachine.
N - Prewash water inlet 3/4" NPT
110°F-140°F
O - Cold water thermostat plumbing
connection 3/4" NPT - Optional
Note: All vertical dimensions are +/- 1/2"
from floor due to adjustable bullet feet.
10
1
4
[260mm]
SECTION 1: SPECIFICATION INFORMATION
AJ-100 STEAM - LEFT TO RIGHT
21
AJ-64 Conveyor Series Technical Manual 7610-003-30-93
Issued: 05-02-2006 Revised: 09-29-2007