Filter
Top Products
3
Check the cooktop serial plate to see if the cooktop is
approved for installation in mobile homes and/or
recreational park trailers. Serial plate is located on the
bottom of the unit.
If approved, the following items are applicable:
Mobile Homes
The installation of a range designed for mobile home
installation must conform with the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part
3280 [formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24 HUD, (Part 280)] or,
when such standard is not applicable, the Standard for
Manufactured Home Installations, ANSI A225.1/NFPA
501A, or with local codes.
In Canada the range must be installed in accordance with
the current CSA Standard C22.1 -- Canadian Electrical
Code Part 1 and Section Z240.4.1 -- Installation
Requirements for Gas Burning Appliances in Mobile
Homes (CSA Standard CAN/CSA -- Z240MH).
Recreational Park Trailers
The installation of a range designed for recreational park
trailers must conform with state or other codes or, in the
absence of such codes, with the Standard for
Recreational Park Trailers, ANSI A119.5-latest edition.
In Canada the range must be installed in accordance with
CAN/CSA -- Z240.6.2 -- Electrical Requirements for R.V.’s
(CSA Standard CAN/CSA -- Z240 RV Series) and Section
Z240.4.2 -- Installation Requirements for Propane
Appliances and Equipment in R.V.’s (CSA Standard
CAN/CSA -- Z240 RV Series).
Installation Of Appliance
The installation of this appliance must conform with local
codes or , in the absence of local codes, with the National
Fuel Gas Code, ANSI Z223.1--Latest Edition, or , in
Canada, CAN/CGA-B149 Installation Code, Latest
Edition.
This appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical Code
ANSI/NFPA No. 70--Latest Edition, or, in Canada, current
CSA Standard C22.1 Canadian Electrical Code, Part 1.
In The Commo n wealth Of Massachusetts
This product must be installed by a licensed plumber or
gas fitter when installed within the Commonwealth of
Massachusetts.
A “T” handle type manual gas valve must be installed in
the gas supply line to this appliance.
A flexible gas connector , when used, must not exceed a
length of three (3) feet / 36 inches.
All supply piping, except as noted, should use common
National Pipe Thread (N.P.T.). For all pipe connections
use an approved pipe joint compound resistant to the
action of LP gas.
CAUTION: Warranty is void on Jenn--Air equipment
installed other than as recommended by manufacturer.
This appliance is designed for use with the appliance gas
pressure regulator supplied with this appliance. It must be
installed in the gas line ahead of the gas manifold
entrance. It is preset for use with natural gas and must be
converted, as described on pages 8 and 9, for u se with
LP gas. (See figures 7 -- 12).
This appliance is designed to operate at a pressure of 5
inches of water column (36″ models), 4 inches of water
column (30″ models) on natural gas or, if converted for
use with LP gas (propane or butane), 10 inches water
column. Make sure this appliance is supplied with and
adjusted for the type of gas for which it is designed.
This appliance was adjusted at the factory for use with
natural gas. If, at any time, this appliance is to be used
with a different type of gas, all of the conversion
adjustments described on pages 8 and 9 must be made
by a qualified service technician before attempting to
operate the cooktop on that gas. Natural gas should be
supplied to the appliance pressure regulator at a line
pressure between 6 and 14 inches of water column or , if
converted for LP gas, between 11 and 14 inches.
If the line pressure supplying the appliance pressure
regulator exceeds 14″ water column (any gas), an
external regulator must be installed in the gas line ahead
of the appliance regulator to reduce the pressure to no
more than 14″ water column. Failure to do this can result
in malfunction and damage to the appliance.
WARNING
Insure this appliance is adjusted for the type of gas
supplied to it and that the gas supply pressure to the
appliance regulator is within the proper pressure range.
S If no other appliance is to be installed in the cabinetry
below this unit, proceed as instructed under paragraph
1, page 4.
S If this unit is to be installed over a Jenn--Air Model
JJW9530, JJW9130, JJW8530 or JJW8130 Series
Electric Wall Oven proceed as instructed under
paragraph 2, page 5.
NOTE: In Canada, gas utilization codes prohibit use of
street elbows. Use standard pipe elbows and make
modifications to these instructions as necessary.