Filter
Top Products
6 7
6.To secure the lid
onto the slushie
chamber, align the
front of the lid
with the front of
the slushie
chamber and
firmly push down
the rear of the lid
until it locks into
position (see fig. 6).
Place the ice chute cap into position in
the lid.
7. Plug the power cord into a 240v power
outlet and switch on.
8. Ensure that slushie dispenser is in the
closed position to avoid spillage.
9. Move the On/Off/Pour switch up to the
‘On’ position.The ice chamber and
slushie paddles will begin to rotate.
10. Slowly pour the
prepared slushie
ingredients
through the lid
opening located
at the rear of the
lid (see fig. 7).
The liquid will
flow into the
slushie chamber
and be rotated by
the slushie paddles and chilled by the
ice chamber.
Note: Do not exceed the “FILL MAX” line on the
slushie chamber.
11. Allow the Slushie Factory to operate
for approximately 20 minutes,
depending on the slushie ingredients or
until the mixture reaches the desired
consistency. Do not turn the Slushie
Factory off during use as the mixture
may thaw.
12.Add more ice cubes and salt if
necessary through the ice chute.
Note: Layer ice and salt until approximately 2.5cm
below the rim of the ice chamber. Exceeding this
may cause overflowing and the slushie ingredients
may become contaminated with salt.
13.When ice peaks form against the
paddles in the slushie chamber, the
slushie ingredients have reached the
desired consistency. Place a serving
glass onto the drink tray, then turn the
slushie dispenser
clockwise to the
‘Pour’ position.
Move the
On/Off/Pour
switch down to
the ‘Pour’ position
(see fig. 8).
The ice chamber
and slushie
paddles will
rotate to assist with dispensing.
14.To stop dispensing, turn the slushie
dispenser anti-clockwise to the ‘Close’
position and move the On/Off/Pour
switch to the ‘Off’ position.
15.Wait until the paddles have stopped
rotating before removing the lid or
slushie chamber from the motor base.
Note: If any moisture or liquid appears on top of
the motor base, ensure the Slushie Factory is
switched off by moving the On/Off/Pour switch to
the ‘Off’ position, then switch off at the power
outlet and unplug the cord. Remove the slushie
chamber from the motor base.Wipe the motor
base immediately with a soft damp cloth and
check that the Slushie Factory is correctly assembled.
DISASSEMBLING THE SLUSHIE
FACTORY FOR CARE AND
CLEANING
Always ensure the Slushie Factory is
switched off by moving the On/Off/Pour
switch to the ‘Off’ position, then switch
the appliance off at the power outlet and
unplug the cord before cleaning.
1. Remove the slushie chamber from the
motor base.
2. Remove the lid by depressing the latch
and lifting upwards.
3. Remove the ice chamber assembly from
the slushie chamber.
4. Discard the ice water and salt from the
ice chamber.
5. Carefully lift locking latches from the ice
paddles and disassemble the ice
chamber assembly.
6.To clean the slushie chamber, fill with
warm soapy water and open the slushie
dispenser to allow clean water to run
through. Use a small, flexible bottle
brush to clean the inside of the slushie
dispenser
7.Wash the lid, ice chute cap, slushie
paddles, ice paddles and ice chamber in
warm, soapy water and dry thoroughly.
This must be done after each use to
avoid salt corrosion especially on the
ice chamber.
8.Wipe the motor base with a soft damp
cloth. Dry thoroughly.
Note: Do not wash any part of the Slushie Factory
in the dishwasher. Hand wash only.
Do not immerse the motor base in water or any
other liquid.
Do not use chemical, steel wool, or abrasive
cleaners to clean any parts of the blender.
STORAGE
Ensure the appliance is switched off and
unplugged from the power outlet. Ensure
all parts are clean and completely dry
before reassembling. Store the assembled
Slushie Factory upright on a level surface.
Do not place any heavy objects on top of
the Slushie Factory during storage.
fig 6
fig 8
fig 7