Filter
Top Products
REFRIGERATOR USE
_!!i!ii_l_ii:i!;i_:l;iii'_iiii_ii_!iiiiiili:_iROi:::;_)_,ii!!_iii_¸¸¸¸_i!_iiiiii¸¸_¸Oiii_ii%;i_!i:/ii;:!!_!:iiiiO__
In order to ensure proper temperatures, you need to permit air to
flow between the two sections. Cold air enters the bottom of the
freezer section and moves up. It then enters the refrigerator
section through the top vent. Air then returns to the freezer as
shown.
Do not block any airflow vents. Ifthe vents are blocked, airflow
will be obstructed and temperature and moisture problems may
occur.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.
Your model may have Digital Controls or Electronic Controls.
IMPORTANT:
• The Refrigerator Control adjusts the refrigerator compartment
temperature. The Freezer Control adjusts the freezer
compartment temperature.
• Wait 24 hours after you turn on the refrigerator before you put
food into it. If you add food before the refrigerator has cooled
completely, your food may spoil.
NOTE: Adjusting the Refrigerator and Freezer Controls to a
colder setting will not cool the compartments any faster.
• If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
• The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
Digital Controls
For your convenience, your controls are preset at the factory.
When installing your refrigerator, make sure that the controls are
still preset to the mid-settings as shown. The digital control panel
is located at the top of the refrigerator compartment and enables
you to view the temperature control set points.
NOTE: The factory recommended set points are 0°F (-18°C) for
the freezer and 37°F (3°C) for the refrigerator.
To turn refrigerator on and view set points:
• Press and hold ON/OFF for 2 seconds.
COLD FREEZER REFRIGERATOR COLD
q=,
COLDER COLDER
To view the Celsius temperatures:
• Press the °C SELECT touch pad. The indicator will light up.
NOTE: If the freezer temperature is below zero, the indicator light
next to the freezer display will light up.
Adjusting Digital Controls
To adjust set point temperatures:
• Press the refrigerator or freezer up or down arrow until the
desired temperature is reached.
REFRIGERATOR COLD
COLDER
NOTE: Wait at least 24 hours between adjustments and then
recheck the temperatures before other adjustments are
made.
The set point range for the freezer is -5°F to 5°F (-21 °C to
-15°C) and 33°F to 41°F (1°C to 5°C) for the refrigerator.
CONDITION: TEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold REFRIGERATOR
- Not set correctly for your Control 1° higher
conditions
REFRIGERATOR too warm REFRIGERATOR
- High use or room very warm Control 1° lower
FREEZER too cold FREEZER Control 1o
- Not set correctly for your higher
conditions
FREEZER too warm/too little ice FREEZER Control 1o
- High use or heavy ice use lower
Electronic Controls
For your convenience, your controls are preset at the factory.
When installing your refrigerator, make sure that the controls are
still preset to the mid-settings as shown.
COLDER FREEZER REFRIGERATOR COLDER
COLD COLD
To turn on the refrigerator:
Press and hold ON/OFF for 2 seconds. The indicator lights show
the current control settings.
10