Filter
Top Products
Attachment
bracket ; ; ;
to ceiling 1
I
I
I
I
I
I
I
I
I
I :
+z&
I ’ I
I
I
I
I
I
I
I
I
l/8"
top
middle
bracket
I
34-518” min.
I
24” min.
3.
The range hood chimney adjusts to meet varying
ceiling heights from 8 feet to 9 feet. Determine and
mark the location of the chimney mounting brackets:
l
Top bracket: l/8’ from the ceiling.
l
Bottom bracket: IO-5/8’ above bottom edge of
range hood canopy.
l
Middle bracket: At the bottom edge of the upper
chimney sleeve.
Note: If canopy is mounted more than 24 inches
above countertop, it may be necessary to cut the
upper chimney sleeve. Use great care not to damage
or bend upper chimney sleeve when cutting.
4
Install the top and middle brackets with ends
n
touching wall and curves facing out. Install
bottom bracket with metal flanges on the bottom.
Check that brackets are securely fastened to wall.
5
Determine and make all necessary cuts in
n
wall or ceiling for ductwork. Install ductwork.
(See “Venting requirements” section, Page 2.)
6
Disconnect power supply. Run wiring
n
through wall or cabinets according to
National Electrical Code and local codes and
ordinances. Do Not turn on power until installation
is completed.
AI
/
w Press on handle in front of filters to release
filters from range hood canopy. Remove filters and
set aside.
8
Remove the terminal box cover from the
n
range hood. Remove the power supply
cable knockout using a flat-blade screwdriver.
Personal Injury Hazard
Because of the weight and size of the range
hood canopy, two or more people are needed
to move and safely install the range hood
canopy.
Failure to properly lift range hood could result
in damage to the product or personal injury.
9
Rotate the two adjustment screws halfway
n
into slots. Hang canopy from flange of lower
bracket, making sure that tabs are fully inserted in
slots and canopy is secure on bracket. Adjust the
height of the canopy by rotating the two screws.
Attach conduit connector to power supply cable
opening so that conduit connector clamping screws
are on inside of range hood. Feed enough power
supply cable through conduit connector to make
electrical connections.
10
Check that canopy is level. If needed,
n
turn adjusting screws until canopy is level.
Electrical connection
Electrical Shock Hazard
l
Electrical ground is required on this appliance.
9 Do Not connect to the electrical supply until
the appliance is permanently grounded.
l
Disconnect power to the junction box before
making the electrical connection.
l
This appliance must be connected to a
grounded, metallic, permanent wiring system,
or a grounding connector should be connected
to the grounding terminal or wire lead on the
appliance.
Failure to do so could result in a fire, personal
injury or electrical shock.
11
n
Make electrical connection:
q
Connect the power supply cable to range hood
terminal box through the U.L.-listed conduit
connector.
l7J Connect the white wire of the power supply
cable with the white lead in the range hood,
using a twist-on connector; connect the black
wire of the power supply cable with the black
lead in the range hood, using a twist-on
connector.
0 Connect the power supply green (green and
yellow) grounding wire under the green,
grounding screw.
l7J Tighten conduit connector screws.
i7J Replace the terminal box cover.
Install chimney
sections
12
Attach damper to exhaust opening on
n
top of canopy using two Phillips-head
screws. Connect ductwork to damper and seal all
connections with duct tape.
13
Position upper chimney on top and middle
Place filters in canopy opening so rear
n
brackets. Slide lower chimney over upper
14
n
edge is over flange. Press filters up
chimney. Slide lower chimney down onto lower
into position.
bracket and canopy for a snug fit. Then secure
chimney pieces to brackets with screws provided.
Check operation
15
n
Turn power on.
I
-.. _
-5zaiz~>~>
control panel = =--.-
location
16
The range hood controls are located in a
n
grey panel on the underside of the
canopy. To open the panel, press up on front edge
of panel and release. The control panel will drop
down.
I
I
“IQ I-la@ -l-o
I
c 3: 0 1
QO1
--mm1
light switch
blower switch
blower speed switch
17
n
Check the operation of the range hood:
q
Move light switch to “1” position. The light
should turn on.
q
Move the blower switch to “1” position. The
blower should operate.
q
Move the blower speed switch to the far left;
blower speed should be LOW. Move blower
speed to right, blower speed should gradually
increase until you reach HIGH speed at far right.
q
Move blower and light switches to “0” position
to turn blower and light off.
If range hood does not operate:
q
Check that the circuit breaker is not tripped or
the house fuse blown.
To get the most efficient use
from your new range hood, read the
“Use and Care Information” section.
Keep your KitchenAid Installation
Instructions and Use and Care Guide
close to range hood for easy reference.
Page
4