Filter
Top Products
Electrical ground is required. See
Electrical requirements.
DO NOT install dishwasher over
carpeted flooring.
Proper electrical, drain and water
supply lines must be available or
must be installed as specified within
shaded-area to prevent interference
with dishwasher frame or other
components. See Electrical, Wate;
and Drain requirements. Plumbing
and wiring should not cross in front
of motor or dishwasher frame.
Product Damage
Protect dishwasher and water
lines leading to dishwasher
against freezing.
Failure to do so could cause
inlet valve, water lines leading
to dishwasher, water lines in
dishwasher and drain to
rupture.
Such ruptures are not covered
by warranty.
For installations where the
dishwasher will be left unused and
subjected to freezing temperatures,
it must be prepared as outlined in
your Use and Care Guide.
IMPORTANT: Observe all
governing codes and ordinances.
Electrical Shock Hazard
1 Electrical wiring and
components must not contact
any plumbing material or
drain hose.
1 Electrical wiring, water supply
line and drain line must not
contact any expose terminals
of dishwasher wiring.
1 Cabinet opening must
completely enclose sides, top
and back of dishwasher. A
side panel and wood top are
available from your
KitchenAid dealer to install
your dishwasher at the end of
a cabinet.
Failure to follow these
instructions may result in
qersonal injury from exposed
Miring.
Corner location - 2” min.
door to cabinets or wall
T!l
33-7116” min.
to 35” max.
underside
counter
height.
If 33-7/l 6”
height is
needed, the
leveling legs
will have to
be removed.
Cut 1” holes for
water, drain and
Grommet
electrical lines
required for
within shaded area.
electrical
cable hole
The unshaded
cut in metal
area must be free
cabinets
of pipes, drain
F
23-112”
min.%
cabinet
depth
hose or wires.
de- 24” opening width A
Figure I
*26” depth4
Figure 2
‘Whisper Quiet
insulation
compressed.
36”
countertop
height
LIE
23-718”
Personal Injury/Product
Damage Hazard
Avoid opening dishwasher
door before dishwasher is
installed.
Dishwasher, before it is
installed, may tip over when
door is opened, resulting in
personal injury or product
damage.
+ 20-314”
I_bp(
Tools and
materials needed
for installation:
Parts supplied for
installation:
2 counterlop anchor screws
Remove screws taped to upper right
hand mounting bracket.
Check that all parts were included.
l
electric drill
l
shutoff valve
l
Phillips
l
supply line fittings
screwdriver
l
1,3/8” NPT street
l
2 adjustable elbow (2 for
wrenches for
galvanized line) OR
copper fittings
90” compression
OR 2 pipe
elbow with 3/S” NPT
wrenches for
at one end for copper
galvanized or
line
iron fittings
l
9/l 6”, I.D. heat- and
l
pliers
detergent-resistant
l
measuring tape
hose and clamps OR
l
flat-blade
5/8”, 0-D. copper
screwdriver
tubing and fittings
.
3,411
nut driver or l
lo”, 5/8” 0.D.
Soft
socket wrench
copper tubing if high
l
wire cutters
loop drain is needed.
l
level
(See Page 3.)
. ,,, drill bit or hole
l
314
II .
strain relief
saw
l
tubing cutter
l
l/8” drill bit
l
pipe-joint compound
l
square
l
twist-on wire
l
112” O.D. copper
connectors
tubing OR 318”
l
electrical tape
We
Page 2