-
the freezer temperature is above 0 °C.
The following displays indicate malfunction. Possible causes
and corrective action (see Malfunction).
-
F0 to F9
-
FE*
-
The power failure symbol
shines.
4 Putting into operation
4.1 Switching on the appliance
Note
u
To switch on the entire appliance it is necessary only to
switch on the freezer compartment.
Switch on the appliance approx. 2 hours before
adding frozen food for the first time.
Do not load food to be frozen before the tempera-
ture display reads -18 °C.
4.1.1 Switching on the freezer compartment
u
Open the door.
u
Press On/Off button, freezer compartment
Fig. 2 (8)
.
w
The temperature display of the refrigerator compartment
indicates the current temperature inside.
w
The temperature display of the freezer compartment and the
alarm symbol flash until the temperature is sufficiently low. If
the temperature is above 0 °C, dashes flash. If it is below,
the current temperature flashes.
4.1.2 Switching on refrigerator and BioFresh
compartment
If the refrigerator compartment was switched off (e.g. during an
extended absence like holidays), it can be switched back on
separately.
u
Open the door.
u
Press On/Off button, refrigerator compartment
Fig. 2 (1)
.
w
The interior light is on when the door is opened.
w
The temperature display shines. Refrigerator and BioFresh
compartment are switched on.
5 Control
5.1 Child proofing
The child-proofing function enables you to make
sure that the appliance is not inadvertently switched
off by playing children.
5.1.1 Setting the child lock function
u
To activate the setting mode: press SuperFrost button
Fig. 2 (12)
for about 5 s.
w
c flashes on the display.
w
The menu symbol
Fig. 2 (16)
shines.
u
Briefly press the SuperFrost button
Fig. 2 (12)
.to confirm.
When
c1 is indicated in the display:
u
Tto activate the child lock, briefly press the
SuperFrost button
Fig. 2 (12)
.
w
The child lock symbol
Fig. 2 (17)
shines. c flashes in the
display.
When c0 is indicated in the display:
u
to deactivate the child lock, briefly press the SuperFrost
button
Fig. 2 (12)
.
w
The child lock symbol
Fig. 2 (17)
goes out. c flashes in the
display.
u
To deactivate the set-up mode: press On/Off button, freezer
compartment
Fig. 2 (8)
.
-or-
u
Wait for 5 minutes.
w
The temperature is indicated again in the temperature
display.
5.2 Door alarm
For refrigerator/BioFresh compartment and freezer compart-
ment
If the door is open for longer than 60 seconds, the
audible warning will sound.
The audible alarm is automatically silenced when
the door is closed.
5.2.1 Muting the door alarm
The audible alarm can be muted when the door is open. The
sound switch-off function is active as long as the door is left
open.
u
Press alarm button
Fig. 2 (14)
.
w
The door alarm is silenced.
5.3 Temperature alarm
The audible alarm sounds if the freezer temperature
is not cold enough.
The temperature display and the alarm symbol
Fig. 2 (15)
flash at the same time.
The cause of the temperature being too high may be:
-
warm fresh food was placed inside
-
too much warm ambient air flowed in when rearranging and
removing food
-
power failure for some time
-
the appliance is faulty
The audible alarm is automatically silenced, the alarm symbol
Fig. 2 (15)
goes out and the temperature display stops flashing
when the temperature is sufficiently cold again.
If the alarm status persists: (see Malfunction).
Note
Food may be spoilt if the temperature is not cold enough.
u
Check the quality of the food. Do not consume spoiled food.
5.3.1 Muting the temperature alarm
The audible alarm can be muted. When the temperature is
sufficiently cold again, the alarm function is active again.
u
Press alarm button
Fig. 2 (14)
.
w
The audible alarm is silenced.
5.4 Refrigerator compartment
The natural circulation of air in the refrigerator compartment
results in zones differing in temperature. It is coldest directly
above the plate separating off the BioFresh zone and at the
rear wall. It is warmest at the top front of the compartment and
in the door.
Putting into operation
* Depending on model and options 5