Filter
Top Products
CAUTION
Risk of injury if the door tips!
u
Take good hold of the door.
u
Set down the door carefully.
u
Unscrew the securing screw on
the bottom right turn hinge.
u
Open the door.
u
Hold the door on the handle side
and at the bottom and lift it.
w
The bearing pin
Fig. 4 (21)
should
come out of the turn hinge
Fig. 5 (2)
.
u
If the bearing bolt
Fig. 4 (21)
doesn't undo press it out from
underneath.
Fig. 4
u
Swing door out at the bottom and remove it.
Fig. 5
u
Unscrew the turn hinge
Fig. 5 (2)
.
u
Unscrew the bearing element,
Fig. 5 (3)
transfer it to the
opposite location hole of the turn hinge and screw it firmly
into place.
u
Take the stopper
Fig. 5 (4)
out of the turn hinge and transfer
it to the receiving hole on the opposite side of the turn hinge.
u
Carefully lift off the cover
Fig. 5 (5)
on the handle side.
u
Undo the screw
Fig. 5 (6)
and transfer it to the opposite side.
u
Put the cover
Fig. 5 (5)
back on.
u
Screw the turn hinge
Fig. 5 (2)
firmly into place on the new
hinge side (with 4 Nm), possibly using a power screwdriver.
Fig. 6
u
At the top, use a screwdriver to unclip cover
Fig. 6 (7)
and
cover
Fig. 6 (8)
at the front, and remove by pulling out and
down.
u
Unscrew the bearing pin
Fig. 6 (9)
and screw it firmly into
place on the opposite side (with 4 Nm).
u
Refit the cover
Fig. 6 (7)
on the side of the bearing pin: insert
at the back, snap in at the front.
u
Fit the cover
Fig. 6 (8)
on the opposite side: insert at the
back, snap in at the front.
Fig. 7
u
Lift the stopper
Fig. 7 (12)
out of the door bearing bush and
transfer it.
u
Detach door handle, stoppers
Fig. 7 (10)
and pressure
plates
Fig. 7 (11)
and transfer to the opposite side.
u
When mounting the pressure plates, make sure they snap
into place properly.
u
Transfer the spring clamp
Fig. 8 (20)
: Depress the
latch nose and pull the
spring clamp off over it.
u
Slide the spring clamp into
place on the new hinge
side until it clicks into
place.
u
Pull the bearing pin
Fig. 8 (21)
out of the door
bush and transfer it to the
opposite side together with
the washer. The latch nose
must point to the inner side
of the door, the notch to
the outer side.
Fig. 8
u
Hang the door on the bearing pin
Fig. 6 (9)
at the top.
u
Swing the door in at the bottom and insert the bearing pin
Fig. 8 (21)
into the turn hinge. If necessary, turn the bearing
pin until it snaps into place.
u
Insert the securing screw
Fig. 4 (1)
at the bottom into the
bearing pin and tighten it (with 4 Nm).
u
If necessary, align the door flush with the appliance housing
using the two slots in the turn hinge. To do so, unscrew the
middle screw.
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough,
the door may drop out. This may lead to severe injuries. What
is more, the door may not close and therefore the appliance
may fail to cool properly.
u
Screw on the bearing brackets/bearing pins tightly (4 Nm).
u
Check all of the screws and retighten if necessary.
Putting into operation
6 * Depending on model and options